Question about Cars & Trucks

Open Question

1994 ford f350 iat sensor

I'm having trouble finding this sensor I have the 460 engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Ford 460 Engine Temp sensor

looking at  the  front of  the engine, just to  the right and behind  the  distributor cap. You  will  see a  wire attached (push on).

Posted on Aug 24, 2008

Ad
Toyota Guy
  • 42 Answers

SOURCE: Location of knock sensor on 1994 toyota 22vre engine

The Knock sensor on a 22re is located under the intake manifold on the engine block. to the upper left of the oil filter. With is the passenger side of the engine. I believe it is yellow in color. Not do be confused with the oil pressure sensor which is close by. The knock sensor has a larger electrical connector. Good luck it can be hard to get to.

Posted on May 06, 2009

Molson02536
  • 3854 Answers

SOURCE: installing chip and want to double check wiring. Need to find IAT/MAF sensor diagram for 2003 Ford Ranger

Save your money, the chip is a ohm resistor at Radio Shack for under $2.00. It splices in to you IAT wire harness located at the intake tube between the air filter housing and throttle body.
Problem with this system is, that you can not adjust anything and have to run a constant 91 octane just to make sure you do not have a Detonation. The ECM will catch the Detonation from the knock sensor and compensate for it by retarding the timing which in turn lose of HP till next start up.
If you like and don't mind the check engine light on once and awhile, you can do the same by just disconnecting the IAT wire harness which give the ECM a 0 resistance thinking it's -20 out side and turn the timing up and lengths the injector pules.
When i was running a Nitro in the Toy before i sold it, i had installed a 10K ohm Potentiometer which you can buy at radio shack for under $5.00 i believe, I just spliced it in to the IAC wire harness so if i wanted to play with the Nitro I'ld turn the resistor up making the engine think it's 185 degrees F and would ****** the timing so i would not hurt the engine. But if i wanted to get more timing i would just turn the knob to drop the resistance to get more time since the engine thinks it's -20 out side.
Hope this helps. Keep me posted if you need more info. Best thing is to do a dyno tune and you can change everything right down to the Shift points.

Posted on May 29, 2009

  • 408 Answers

SOURCE: code came back as iat sensor reading high

IAT stands for Air Intake Temperature Sensor and it is located in the intake tube coming from the air filter box tot he engine. Easiest way to find it is look at the top of your engine where it says 2200. Coming right out of that manifold is a black ribbed tube about the size of a baseball to softball. It should be going towards the direction on the front drivers side. on the back side of that tube, about 4 inches away from the intake manifold (the things that says 2200) is a plug with wires. That is your IAT Sensor. If it is unplugged, plug it back in. Otherwise unplug it and replace it. Make sure to disconnect the battery while you do this so the computer resets itself after the new one is installed. Thanks and please don't forget to rate!

Posted on Jul 15, 2009

emissionwiz
  • 76164 Answers

SOURCE: IAT sensor location

here is a picture


0d597dc.jpg

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 ford f350 7.5 460 i have problems with the high idle in park sometimes other gears mostly park the funny thing is when cold it runs at 1,000 rpm and when hot it go's 1,250-1,450 i replace the


Check the engine intake and all vacuum hoses for leaks, do this with a can of spray carb cleaner, if you hit a leak the idle speed will change. Repair what you find.

Aug 09, 2012 | 1992 Ford F350

1 Answer

1994 Ford Ranger 4.0L IAT location?


Hi there:
You vehicle had a seperate IAT sensor it mounts into the intake on the drivers side about half way back the wire colors are GY and GY/RD. Here is a pic of the location see bottom right for 4.0L...
6_15_2012_6_36_57_pm.gif


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 15, 2012 | Ford Ranger Cars & Trucks

1 Answer

I'm trying t locate my IAT sensor on my ford escort 1994 and i cant find it


it is located on the inlet for the throttlebody on a section between the throttlebody and the air intake tube from the airbox. Do you have a North American model or a European model? The European model didn't require an IAT sensor. Just the North American model to meet EPA requirements. If it's a North Americal model, the sensor should be located in the air cleaner and have 2 small hoses attatched to it. have a good day !!

Jun 18, 2011 | Ford Escort Cars & Trucks

1 Answer

What's the firing order for 1995 460 engine


For the 1995 Ford F350 V8: 460 cubic inch = 7.5L Engine:

Firing Order:
1-5-4-2-6-3-7-8

Cylinders:
....(back)....
|..4........8..|
|..3........7..|
|..2........6..|
|..1........5..|
.....(front)

Distributor:
....(back)
....[X]..5
...4.............1
2........O........8
...6.............7
..........3...[X] - clip
......(front)

Let me know if this helped, or if there is additional information or questions. Feel Free to contact me at FixYa.com!

Apr 27, 2010 | 1995 Ford F350

1 Answer

I have a 1995 Ford F350 460 engine it sometimes


you need to check fuel preasure and change your fuel filter

Nov 02, 2009 | 1995 Ford F350

1 Answer

1991 ford f350 460 gas to a 1994 7.3 powerstoke any help?


It would definately be easier and probably cheaper to trade trucks than to change motors. You will have to gut the 94 engine compartment for wire harness, filters, brackets, rad, coolers, computer,sensors. You will need to find a way to fit warning lights into your dash because the 94 dash would be different. Check to make sure your fuse box will work with the diesel harness installed or that you can make it work. Fuel lines and fuel pump need to come off the 94. Diesel ones are different from gas. It will be a lot of work and time. For me the price would have to be real good. Hope this helps.

Oct 26, 2009 | 1994 Ford F350 Crew Cab

1 Answer

Im putting in the boss performance module


please rate as problem solved if this is what you need.



Section 03-14: Engine Controls, Electronic 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Intake Air Temperature (IAT) Sensor Removal and Installation
  1. Disconnect battery ground cable (14301) .
  1. Disconnect engine control sensor wiring (12A581) from intake air temperature sensor (IAT sensor) (12A697) .
  1. Remove intake air temperature sensor from air cleaner outlet tube (9B659). (This is the tube that goes from the air cleaner to the engine.)
  1. To install, reverse Removal procedure. Tighten intake air temperature sensor securely.
--------------------------------------------------------------------------

Jun 02, 2009 | 1994 Ford Mustang

1 Answer

New truck no specs


10W30 should be fine unless that is a diesel engine... automatic transmission takes Type F fluid. Just looking around to see if i have the repair manual for that truck.

Robert

Jan 26, 2009 | 1994 Ford F350 Crew Cab

1 Answer

High idle when in drive


Sounds like a faulty TPS sensor, also could be the ECM playing games with you,,,try disconnecting the battery for about 20 mins,,then reconnect,,it may clear it up.

Jan 17, 2009 | 1994 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...