Question about Cars & Trucks

Open Question

Freightliner cascadia fault codes

Sam controller sht lo 249 s 254 04

Posted by Anonymous on

3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: 2011 freightliner Cascadia with DD15. Fault code


Posted on Mar 26, 2011

  • 1207 Answers

SOURCE: 2010 freightliner cascadia with abs code SAE 254

the abs light is on, it telling you that there have a problem on your abs system, such as simple wiring issue with a sensor, or it could be as bad as an abs module. it need to be plugged into a OBD2 code scanner/reader to know exactly what part triggered the code.

Posted on Aug 09, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2011 Chevy Silverado low beams are not working everything else works but the low beams and someone please give me a diagnosis thanks.

Your low beams are controlled by the Vehicles BCM - body control module . The BCM energizes the HDLP LO/HID relay located in the under hood fuse box , sending B+ voltage to fuse's # 12 & 16 both 20 amp . LO HDLP - LT & LO HDLP - RT , These are B+ voltage for low beams . Your headlamp low beam relay could be bad or if the BCM isn't energizing it could be a switch problem . Do you know how to do basic automotive electrical testing using a volt meter . Videos on youtube ,plus video's on reading wiring diagrams .You can find free wiring diagrams at Also watch testing relays

Jan 18, 2017 | Cars & Trucks

1 Answer

My 2008 mercedes ml550 power lift gate has quit working and all lights on rear of vehicle quit working, turn signals, 3rd brake light, reverse lights, rear camera. On occasion all work ok

You should check the rear sam control unit.It is located in the right hand side of the trunk.remove the panel and you will see a fuse block.look directly below it.that is where the rear sam is located.remove the connectors and check for corrosion.this is a very common problem.the rear sam will need to be coded so take it to a reputable repair facility.

Dec 12, 2016 | 2008 Mercedes-Benz Mercedes Benz Ml Class

1 Answer

Tengo una Lincoln Mkx 2007 con 69900km y al girar el switch con su llave adecuada prende el candado y se apaga intermitente y da un pitido de aviso bajo el tablero y no enciende regreso el switch a...

Puede ser un modulo que esta malo eso es lo mejor llevar lo al dealer para que lo chequen.

Mira ver si lo puedes llevar a advance auto parts para que te chequen el alternador puede ser que esta mandando mucho voltaje a lo modulos y causa que el systema se apague.

Feb 03, 2015 | 2007 Lincoln MKX

1 Answer

What is sht. on my amp mean

Short I do believe.

Jul 03, 2012 | Cars & Trucks

1 Answer

How do you change the frount sam?

must get your car to dealer workshop should need diagnose cpu to replace sam because need re coding new control unit otherwise most of function will not work in your car.

Dec 15, 2010 | 2001 Mercedes-Benz C-Class

1 Answer

When trying to start my car it will run for a few secs and then sht off..why would this be happening?

try checking the ignition module,if good could possilbly be the ecm,or maf sensor,have them checked.


Oct 23, 2010 | 2000 Buick Regal

1 Answer

Shifts into 4 lo without warning

Sounds like you have a faulty transfer case control module which is located on the passenger side under the dash area right at the kick panel,there isnt any real test for this TCCM except replace with known good one.

Oct 31, 2009 | 1999 Chevrolet Blazer

1 Answer

I have the same problem when mt light comes on my car runs like s

change the mass air flow meter.If its faulty that will cause so many different faults to come up.

Jul 17, 2009 | 1990 Cadillac Deville

1 Answer

My 2001 GMC Jimmy is stuck in 4 Lo.

i believe those are vacuum controlled on top of the transfer case is a plug with 3-4 vacuum lines going to it,you will need to take it out and see if the check ball is stuck if it is it needs to be replaced

Nov 12, 2008 | 2001 GMC Jimmy

1 Answer

Mercedes c class c180 2001

hi,rear sam control ,fuel gauge,tail light,depends what equipment install at the rear,ty

Oct 01, 2008 | 2001 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides