Question about Cars & Trucks

1 Answer

Falcon helicopter controler item#35040

Controller shuts of when operating controller

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,691 Answers

This is a car or truck question?

Posted on Jul 23, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does a ba falcon shut off when hot left for half an hour it will start again


very annoying and could be dangerous
after what has been fitted
leaves the coil packs/ spark issue
idle control sensor
02 sensor
the maf
other unknowns

a shut down like that ..could be a module of a sensor
the engine light should be on
saying the engine computer has fault codes to read


down load the free repair manual of you dont have one
only one download not for resale etc etc
Ford Falcon BA 2002 2005 Workshop Manuals Factory Service Manuals

good you replaced the CAS
first thought was the crank angle sensor
you toss water on it and if the car starts up its faulty

Oct 14, 2016 | Cars & Trucks

1 Answer

Why does my helicopter dont want to start


Make sure that your battery for the helicopter is still good. You will have to put a meter on it.

Jan 01, 2015 | Cars & Trucks

1 Answer

Does fuse or relay operate heating/cooling fan BA falcon


normally fuse controlled but remember that inside the heater bopx are 3 resistors that alter fan speed when you change the knob position on the dash. They do burn out and have to be replace to make the fan work

Jan 19, 2013 | Cars & Trucks

1 Answer

How to adjust idle on ford falcon el 6 cylinder


wam the car up, disconnect the idle speed control valve wiring plug (idle control valve sits on top of the throttle body) then set the idle to 700rpm with the grub screw stop just above where the throttle cable fits to the throttle body. Reconnect theidle control valve and you're done. It may take a few k's driving for the ECU to relearn the new throttle stop position. The idle speed control valve is only used by the ECU to add idle speed when extra load is put onto the engine such as power steering or air con use, the base idle is set mechanically on the old falconns.

Oct 04, 2009 | 1983 Ford Fairmont

1 Answer

1998 Grand Marquis parking lights won't shut off


If your car has no AFTERMARKET electronics such as an alarm system or remote start .... 1998 Marquis Has a headlamp switch that supplies a negative signal to the BCM (body control module) located to the right of the accelerator petal and up a bit towards the heater control area in the dash ... if there are no other offending items it will be either the BCM the switch or wires ... if you have aftermarket devices (that operate the parking lamps) .. I would check those first, just because. Note: the BCM is very expensive,

Jan 06, 2009 | 1990 Mercury Grand Marquis

1 Answer

1997 ford falcon fairmont,the led display for climate control and odometer does not light up


Never heard of a 97 Ford Falcon Fairmont. What model do you actually have. Ford quit making the Falcon and the Fairmont many years ago.

Nov 09, 2008 | Ford Fairmont Cars & Trucks

1 Answer

CRUISE CONTROL ON MY AU FALCON FORTE DOSE NOT WORK. IT INDICATES THAT IT IS ACTIVATED BUT I CAN NOT SET IT TO A SELECTED SPEED


hi on some uk models with cruise control thet as you know trips out as you press foot brake ? one of the prob's with what you describe ? indicating operative but not setting ? just have a look around brake pedal area near the pushrod that pushes master cylinder/power vac you may find either a vacuum small diam hose connected fom power vac to a small cyl nearby that as brakes operated this cyl which has hose trips off and releases c/control ? or your car may ? have electric solenoid switch adaption that works as brakes applied and trips off c/control so you are looking for any vac leak audable ?? or elec device/switch that may have fault or is stuck in off position resulting in c/control being told brakes pedal pressed ?? the uk galaxy has the vac type c/c and the vac mini hose splits renew pipe and working !

Nov 04, 2008 | Ford Fairmont Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...