Question about Cars & Trucks

1 Answer

How and where do I top up a kj 94 model ford laser transmission and clutch

Posted by on

Ad

1 Answer

No vehicle consumes any fluids
No need to top up anything
If you find ANY fluid low, you have
a leak to repair

Posted on Jul 24, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 94 ford laser clutch

easy look on top of gearbox or transmission to see if there is a cable or hydraulic piston which ever there is thats wat it is

Posted on Dec 02, 2008

techbuster
  • 5081 Answers

SOURCE: how do i change fuel filter on a ford laser kj iii

It is a clear plastic container like a small pill bottle on the fuel line. You just need to unclamp the old one and clamp the new one in place, making sure you fit it excatly the same as way as the old one. It should have an arrow on it.

Posted on Jul 06, 2009

fixyathing
  • 341 Answers

SOURCE: I need instructions on how to change timing belt

it basically the same with the other engines...as long as you know what parts to remove. Just make sure that before you remove the belt/s and tensioner/, the timing marks are in the right place. I have changed timing belts without instructions...experience is needed though. I suggest better get a service manual to be sure if this is your first time.

Posted on Aug 10, 2009

  • 752 Answers

SOURCE: hi, Whats the ignition firing order of 1999 ford

try 1342

Posted on Feb 14, 2010

  • 270 Answers

SOURCE: Where is the water pump

The water pump on the 92 Laser is easily replaced. You just need to untension the the belt driving the bump. Once you have done that all you need to do is undo the bolts and take the pump into your local auto parts dealer. Now that you have the pump install it and retension the belt.

U actually have to remove alternator belt and powersteering/a/c belts, then remove timing belt cover, remove timing belt adjuster, and slide timing belt off top pulley, making sure you mark it before removing it, so as to put it back in same position. Next, unbolt 2 bolts at bottom of water pump (this is a bit fiddly, but doable, then, undo water pump, replace with new water pump, being sure to use gasket cement, aswell as new gasket, which should be supplied with pump, then put it all back together, in reverse order of removal. Fill cooling system, check for leaks, and voila, u have done it :)

Check this at ehow.com

Posted on Nov 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

94 ford ranger manual transmission slipping when going up hills and when accelerating please help


Try adjusting the clutch. If it doesn't work you are going to have to replace the clutch and pressure plate along with the throwout bearing.

Apr 24, 2017 | Ford Cars & Trucks

1 Answer

Im trying 2 locate where to put the clutch fluid in my 94 ford laser 1.6 glxi 5d


normally its brake fluid on the master cylinder there a hosethat goes or containr that bring oil to the master cylinder of the clutch

Apr 11, 2015 | Ford Laser Cars & Trucks

1 Answer

Ford laser sedan kj lxi 95 model break lights need to be replaced


are both brake lights not working ? if so very unusual for both to go at same time so i'd check the fuse , fuse box lower dash drivers side lid/door will have list , if ok open the trunk and at the rear of the light clusters remove the brake bulbs, there will most likely be some sort of trim, carpet or even a small access panel to remove first,if bulb's are ok then it must be the switch which is located at the top of the brake pedal, easy to adjust disconect the wire from top of switch and turn switch anti clockwise one complete turn , refit wire and check if bulbs working , if not repeat the adjustment

Mar 11, 2015 | Ford Cars & Trucks

1 Answer

Ford Kj Laser Auto gear changes **** the car while driving


if you know nothing about cars then I suggest taking it to a shop that specializes in transmissions. if you insist on doing it yourself, get a repair manual that covers your vehicle. should cover it.

Feb 01, 2013 | Ford Laser Cars & Trucks

2 Answers

My 1998 KJ Ford Laser drives fine but after you drive approx 15km's it starts to lose power badly


If this happens each time you drive it, check the fuel filter. It may be almost clogged and slow the fuel delivery. A other place to look would be the spark plug and coil wires. ( not sure what type to system your Laser would have.) The resistance in the Laser's plug and coil wires can increase as it warms up when it is driven. If the wires are over 5 years old they should be replaced.

Jun 03, 2012 | Ford Cars & Trucks

1 Answer

I got a 94 ford laser not starting (not flat bat)


At a time when it will not start, try hitting somewhere deep in the engine/transmission with a tool like a hammer..
or, if you can find where your starter motor is, tap there with the hammer.
The starter solenoid gets stuck and needs to be rebuilt/replaced.

Aug 31, 2009 | 2006 Ford Laser

2 Answers

I need instructions on how to change timing belt on Ford laser 1995 KJ model please


it basically the same with the other engines...as long as you know what parts to remove. Just make sure that before you remove the belt/s and tensioner/, the timing marks are in the right place. I have changed timing belts without instructions...experience is needed though. I suggest better get a service manual to be sure if this is your first time.

Aug 10, 2009 | Ford Laser Cars & Trucks

2 Answers

My clutch won't engage


There is a rubber plug on the bottom of the transmission bellhousing. Remove the plug and look in to see if the slave cylinder is leaking. If yes the transmission will need removed to replace it. While you are there, check the clutch disc and pressure plate and replace as needed.

May 27, 2009 | 1994 Ford Ranger Supercab

1 Answer

94 ford laser clutch


easy look on top of gearbox or transmission to see if there is a cable or hydraulic piston which ever there is thats wat it is

Dec 02, 2008 | 2006 Ford Laser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...