Question about Cars & Trucks

Open Question

1999 chrysler 300m fuel filter location - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76682 Answers

SOURCE: need location of coolant sensor on 2002 chrysler 300m

near the thermostat I think, look for this part.

f2e8303.jpg

Posted on Apr 22, 2009

Ad
morganismo
  • 36 Answers

SOURCE: AC belt on 1999 Chrysler 300M

When you replace the AC belt you really should replace the serpentine belt as well, since you will have to take it off already. If you don't do it now it is inevitable that you will have to replace it in like 3 weeks anyway : )

You need to first remove the serpentine belt by loosening the nut in the center of the idler pulley. After that you will need to loosen the push bolt on the side of the idler pulley. The hub bolt is a 15mm size and the push bolt on the side of the tensioner is a 13mm I think. After you loosen it sufficiently, you will need to pull off the old belt.

Next you will need to loosen the tensioner pulley for the AC belt as well. It is the same process. The main issue is space. You will most likely need to raise your car to get at the right angles to loosen these pulleys.

Once you loosen the idler pulley in the same manner as you loosened the other, you can slip the AC belt onto the back of the crank pulley and route it as the diagram under your hood instructs you. Next tighten up the idler pully in the opposite way as you loosend it...tighten up the push bolt until the belt play is within factory specifications, then tighten the hub bolt in the center of the pulley. Do the same for the serpentine belt and you should be up and running in no time. I just performed these tasks on my 2000 300m and I wish someone would have told me this before I started my project. Hope this helps, Good Luck!

Posted on May 26, 2009

  • 7 Answers

SOURCE: programming instructions for a 1999 Chrysler 300M remote fob

Manual Programming Procedure (non scan tool)
1. Connect pin 1 of the 16-way data link connector to chassis ground or to pin 4 of the 16-way data link connector.
2. Close all doors, turn ignition key to off.
3. Turn ignition key to Accessory.
4. Turn ignition to off, door locks will cycle once (in programming mode).
5. For each key FOB, press any button 3 times in a row to program code. When programming is complete, the door locks will cycle once.

NOTE:
IF A SECOND KEY FOB REQUIRES PROGRAMMING, IT MUST BE PROGRAMMED WITHIN 1 MINUTE OF PROGRAMMING
THE FIRST FOB PROGRAMMING. PRESS ANY BUTTON ON THE SECOND FOB 3 TIMES TO PROGRAM ITS CODE. WHEN PROGRAMMING IS COMPLETE, THE DOOR LOCKS WILL CYCLE ONCE.

6. The programming mode finishes after the following:
a. Programming of two key FOBS is completed.
b. One minute has passed since programming.
c. Pin 1 of 16-way data link connector is removed from ground connection.
d. Ignition switch is turned on.
e. Any of the doors are opened.

Posted on Jun 25, 2009

c17hydro
  • 2984 Answers

SOURCE: need to replace a idle air control valve on a 1999 300M Chrysler

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the IAC electrical connector.
  3. Remove the IAC mounting screws.
  4. Remove the IAC.



da3669e.gif

To install:
  1. Install the IAC to the throttle body.
  2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
  3. Attach electrical connector to the IAC.
  4. Connect the negative battery cable.
  1. Disconnect electrical connector from IAC motor.
  2. Disconnect air plenum (where applicable).
  3. Remove two mounting bolts (screws).
  4. Remove IAC motor from throttle body.

3ccd55e.gif

To install:
  1. Install IAC motor to throttle body.
  2. Install and tighten two mounting bolts (screws) to 60 inch lbs. (7 Nm) torque.
  3. Install electrical connector.
  4. Connect air plenum (where applicable).

Posted on Mar 06, 2010

ZJLimited
  • 17970 Answers

SOURCE: where is the thermostat located on a 1999 chrysler

The thermostat is located in housing on lower left side of engine block near oil filter and attached lower radiator hose.

4f256f5.gif

hope helps.

Posted on Jun 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my fuel filter located on my 2001


I think the last year they used a replaceable filter was 1998.
No fuel filter used on your model.

Sep 28, 2014 | 2001 Chrysler 300M

1 Answer

Fuel filter location 2000 chrystler 300m


Hi Harry, I'm glad to help! The fuel filter on a 2000 Chysler 300 is inside the fuel tank mounted on the end of the fuel pump module. Hope this helps and have an awesome day Harry.

Apr 24, 2014 | 2000 Chrysler 300M

1 Answer

The thermostat don't work where is it located at to put it on the 99 chrysler 300m


Jacquelin! The thermostat n a 3.5 Chrysler 300M is on the block right next to, and toward the front of the engine by the oil filter. Yes, that sems a bit strange, but then I'm not a bit surprised about this engine any more. As the big radiator hose leaves the radiator finding its' way toward the block, it terminates at a traditional "goose neck" at the block behind the power steering pump- only accessible by removing the oil filter and using an extension and a u joint BUT FIRST: lower the anti freeze in the system by draining some fluid. But anyway- THAT'S where it is. Have fun, fix it up and GO!

Dec 12, 2011 | 1999 Chrysler 300M

1 Answer

Where is the thermostat located on a 1999 chrysler 300m?


The thermostat is located in housing on lower left side of engine block near oil filter and attached lower radiator hose.

4f256f5.gif

hope helps.

Jun 17, 2010 | 1999 Chrysler 300M

2 Answers

Where is the Battery in a 1999 chrysler 300m


It is located under the air filter. On the left side of the engine compartment.

May 10, 2010 | 1999 Chrysler 300M

2 Answers

I,m can not founded fuel filter,wich place?Thanks


The Fuel Filter is located: Under vehicle, center, below seating area, mounted on top of fuel tank, in fuel pump module

Jul 29, 2009 | 1999 Chrysler 300M

1 Answer

2000 Chrysler 300m


If I remember correctly... On the drivers side, about midway, above the tie rod.
It's a tight squeeze to remove. recommend the type of filter grip that goes on the end of the filter.
The band type is tedious due to limited room to grip and turn.

Dec 09, 2008 | 1999 Chrysler 300M

1 Answer

I cannot find the location of the oilpan and filter


if you are not sure of this please take it to a shop and get professional help sorry do not struggle with it.!!!

Dec 04, 2008 | 1999 Chrysler 300M

1 Answer

Location of the oilpan and filter of my 1999 Chrysler 300M


there is a large plastic cover/shield under the car, remove it and the filter and oil pan are right there, the filter is in the front.

Dec 04, 2008 | 1999 Chrysler 300M

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...