Question about 1997 Oldsmobile Achieva

1 Answer

Where exactly are all altenattor bolts

Need to know were all bollts are

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 49 Answers

Depending on motor it will have 2 or 3. most newer gm products have long bolts that go in from the side of the alternator and bolt it directly to engine block or cylinder head

Posted on Jul 23, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My G6 need a bolt on the passenger side door so that it can stop popping when I open it I need the size of that bolt?


Is there another bolt, passenger door, that you think is the same size, or on the other door? If so, remove that bolt, take it to hardware store, show them, tell them you need another bolt same size and thread. Hopefully they can fix you up?
I have to say, I can't see anything from here, I don't know, exactly, which bolt your talking about?

Oct 13, 2016 | Cars & Trucks

1 Answer

I have a 79 gmc c15 royal sierra heavy half it has the 12 bolt pattern on the rear end cover & I'm needing the torque spec for the bolts for the cover


These don't need to be very tight, same as trans pan bolts or maybe a little more. Don't know exact spec, but perhaps 8 ft. lbs.?

Mar 28, 2015 | GMC Cars & Trucks

1 Answer

What does it mean when battery sign is still on dash after i put a new altenattor in 2001 windstar van


It means it's not charging , could have a bad fuse ! Check voltage at the large wire on the back of Alternator , should read battery voltage. Two fusible link's supply power , well it will read battery voltage if not open . if open fusible link is burnt .This is the charge line from alternator to the battery. An there is a three wire connector plugged into the alternator. One has Battery voltage an the other two go to the PCM - powertrain control module . for control ! Do you know how to use a volt meter ! Diagnosing Alternator Problems EricTheCarGuy

Feb 06, 2015 | 2001 Ford Windstar

1 Answer

I need the torque specs


It may help to know exactly what vehicle you are asking about. It's a little bit vague at the moment.

Mar 27, 2014 | Cars & Trucks

1 Answer

97 Nissan pickup standard cab XE, I am looking to convert from bench seat to bucket seats. Does anyone know of an exact fit, bolt hole match up, no drilling? Will seats from other Nissans fit ie a...


The bucket seats from the 1995 Nissan Pathfinder should be an exact fit. The bolt holes and bolts should be the exact same and have the exact same hole locations.

Aug 22, 2011 | 1997 Nissan Pickup

1 Answer

How do i change a starter on a 92 buick lesabre and can i get a bolt pattern for it


I dont know what you need a bolt pattern for exactly, usually you just need to locate the starter. Disconnect all the wires from it, noting their locations, and unbolt the bolts and it should come right out.

Mar 11, 2010 | 1992 Buick LeSabre

1 Answer

How do I replace the parking brake cable on my 97 Grand Caravan SE 3.3L? it's broken midway where the sliding door starts on the driver side??


well usualy you only have to replace half of it because it is set up like a Y the portion that come from the parking break or handel just clips in to a slide so when you pull or push the parking break down it puls the cable tight the back of it usualy bolts to clips whare the Y starts and is adjustable so un clip from the pedal and un bollt it now i sgest before you pull it out use the borken line as a pull string to feed it throug by taping them together.

Jun 04, 2009 | 1997 Dodge Grand Caravan

1 Answer

Mixed my bollts


Count the bolt holes and you should have a matching number of bolts. All the same size and length. you can also use the pan gasket for the pattern.

Jun 02, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Oldsmobile Achieva Logo

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...