Question about 2003 Jaguar X-Type

1 Answer

Key fob Does this method of re-programming work with the switch blade key FOB? I've been told that dealer must do this. Just got the car and 1 of the 2 FOB's don't work. I could replace the battery in it, but it still needs to be re-programmed after that correct? Grabenfish@yahoo.com

Posted by on

1 Answer

Use your owners manual to program the key
Don't need a dealer,you just need the info on
the procedure,a dealer may give that to you
free,if not don't get involved with them,ask a local
shop for the procedure

Posted on Jul 23, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

raygin
  • 322 Answers

SOURCE: 2003 Jaguar S-Type, programming a key fob

The switchblade key would need to be compatable with your ignition switch barrel. Only normally available from jag dealers who check the Jag owners register before supplying you a replacement.
The older type seperate fobs could be programmed by switching the ignition on and off 8 times (allowing all functions to settle) and on the 9th switch on - press a button on each fob and then switch off. to test use a good fob to lock the car then try the reprogammed fob to unlock/lock. Sometimes this works first time - sometimes needs a couple of tries.

Posted on Apr 03, 2009

raygin
  • 322 Answers

SOURCE: How do I program S Type Jaguar key fob Year 2000 Jag ?

Seperate key fobs only can be programmed in the following way.

Turn ignition on/off 8 x times (allow all functions to stabilise) after the 9th on - press a button on both remote fobs. then turn ign. off. use good remote to lock and then try new remote to unlock/lock. sometimes it works first time - sometimes you have to repeat actions. good luck.

Posted on Apr 07, 2009

raygin
  • 322 Answers

SOURCE: Key fob won't work on my 2003 jaguar s type car

Try this .. it MIGHT work.
Clean carefully the battery contacts and check there is no large build up of dirt around and on the small printed circuit. Insert new battery and then try a manual reprogram by following these instructions which work for the older style seperate key fobs - never tried it with new switchblade type keys, which I am assuming this is?
Turn on/off ignition 8 x times allowing all functions to settle each time. on the 9th on press a buttom on each remote and then switch off ign. Use the good key to lock the car then try the new key to unlock. sometimes it works first time - sometimes it takes a couple of tries - hope it works for you.

Posted on Apr 08, 2009

  • 52 Answers

SOURCE: 2003 Jaguar S-Type, programming a key fob

If its a new key fob the only way you can program it is this the factory scan tool, u'll have to take it to a dealership for them to do this and they will charge you .5 hrs for labor.only x-types can be programmed without the jaguar software. Im guessing it will cost you between 40 and 50 bucks to have them program it.

Posted on May 11, 2009

  • 1 Answer

SOURCE: car key fob not working and locking car

i have a rover 25 and the key fob is not opening the car i could use the key to open it but the alarm will go off and cant stop it without the fob...

Posted on Apr 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mitsubishi magna 3.5 v6 tk 1999,car was running,but now it just turn over, but it will not fire to start the engine. I been told it the immobiliser. so how doI get the immobiliser to reset it self.


you dont,
When the anti theft system was created,the dealers forgot to tell the new car buyers about how much the fob matters to the vehicle,without it,owners are stuck,your anti theft device is activated,you need to lock and unlock your doors a couple times with the key fob,not the key,and then you need to put the key in the ignition and start it,if you dont have your key fob,call your car dealer to get a new one,they are programmed for each car only,you cannot bypass it.if you lost your fob or never had it,whatever,you need to have the exact fob that came with that car from the factory,the key and fob have a chip in them that only go to that certain car,if you do not have it,then you need to buy a new one from the dealer or ebay and then you need to contact your dealer about programming the fob to your car,you might not have to have it towed if they have the documents from the car,the only other way is to get a junk car,with the steering column,key,fob and all computer boxes and door locks and switch them,i just did that with a 98 dodge dakota,and it works.

Jul 07, 2015 | Mitsubishi Cars & Trucks

1 Answer

Program new key fob for Cadillac cts 2003


There are several methods of doing this - but your 2003 requires that you either go to the dealer for them to add a FOB with special equipment (ask if they'll do it for free - can't hurt). If you have time to kill, you can do it yourself with Method 3 as described and found at:

Key Fob Reprogramming General Cadillac Forums

Method 3 - Key Fob Auto Learn


This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Good luck!

Feb 25, 2015 | 2003 Cadillac CTS

1 Answer

How to program a keyless fob for 2001 cadillac deville


Unfortunately, the website I found says there is no on-board method of programming your car for a new key-fob. You have to take the car to a dealer or to a key-maker (who may only charge half as much as the dealer)

Key Fob Remote Programming Instructions 2001 Cadillac Deville Key Fob...

Feb 22, 2015 | 2001 Cadillac DeVille

1 Answer

How do I program my key fob to a 94 Olds 98 regency?


Assuming it's a standard GM half moon style key fob, you can get replacements soon many sources including dealerships, locksmiths, and ebay.

Programming depends on whether you already have a working key?

If you don't, you will have to go to a dealer or find a locksmith who has the right equipment (I suspect not many do).

THis works for Holden Commodores of that era, most GM products should be similar:
If you have a working key, it's relatively straight forward, as the car can program new keys.
1 remove screws holding key blades into the remote heads of both keys.
2 remote the key blade from the *new* key and put aside.
3 insert old (working) key into ignition and start the car.
4 with car running, carefully slide the remote head off the key in the ignition barrel. Car should stay running.
5 carefully slide new remote head onto the old key blade sitting in ignition. Make sure the metal contact inside the key blade insert makes contact with the key blade. Make certain the small contact pin on the facing edge of the remote makes contact with the metal slide ring on the outside of the ignition barrel - these two contacts form a circuit.
6 The key fob should program almost immediately, but leave the fob in position for 30 secs to a minute to ensure its done.
7 turn car off and reassemble keys.
8 test all functions of new key - remote entry and engine start.

(get key blank cut by a locksmith before commencing the above!)

Feb 09, 2015 | Cars & Trucks

1 Answer

Can I program my replacement fob key without going to the dealer if I don't have an extra key


there are many shops who can program your key and much more easier if you have a working fob key already.If not it is good to take your car to the shop with the new fob key and they will do it for you,I believe with less money than the dealer. Ask and try it.

Sep 02, 2012 | 2008 Dodge Charger

1 Answer

Replaced chip on key on 91 DTS and car lost all power while driving. It shut down and nothing works.


There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
Method 1 - Key Fob Quick Learn This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward.
A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Install a scan tool.
Use the scan tool, to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 3 - Key Fob Auto Learn

This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 4 - Service Programming System Fob Programming

This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

Place the vehicle in the Vehicle On, Engine Off mode.
Connect a scan tool to the vehicle.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
Turn the vehicle OFF.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
When the 10 minute relearn procedure has completed, use the scan tool to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Oct 26, 2011 | 2006 Cadillac DTS

1 Answer

Keyless entry remote programming


Hello here is the instructions for programming the key fobs

This procedure will add, replace, or invalidate all key fobs. This procedure requires that you have a known good key fob available, a new/replacement key fob, the vehicles mechanical key, and a scan tool.
Method 1 is also used for the initial programming of fobs to a new replacement RCDLR. In this instance, the new RCDLR comes ready to learn the first key fobs introduced. Perform the learn procedure as outlined, with the exception that the new RCDLR does not require a known good key fob be placed within the interior of the vehicle.
Note: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Methods 2 or 3 must be used in this instance.
  1. The vehicle must be OFF.
  2. Place a known key fob and any new/replacement key fob(s) to be programmed in the cupholder inside the vehicle. DO NOT place any fobs in the console fob pocket at this time.
  3. Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
  4. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4). → If the DIC displays: OFF/ACC TO LEARN, the known fob has not been recognized. At this time, programming will revert to Method 2.
  5. If the DIC is displaying the correct fob number that needs to be programmed, skip ahead to step 9.
  6. If the DIC is not displaying the correct fob number that needs to be changed (i.e., the DIC is displaying: READY FOR FOB 3, and you wish to program FOB 1), use the scan tool to access the following: • Vehicle Control Systems • Computer/Integrating Systems • Module Setup • Remote Control Door Lock Receiver • Program Key Fobs
  7. Select the fob position you wish to program: Note: Selecting Invalidate All Fobs will erase any known fobs and will cause the DIC to prompt READY FOR FOB 1, requiring all fobs to be relearned to the vehicle.
    • Invalidate All Fobs • Program Fob 1 • Program Fob 2 • Program Fob 3 • Program Fob 4
  8. With the fob position selected, press the PROGRAM soft key on the scan tool. The DIC should display: READY FOR FOB X (X = fob 1, 2, 3 or 4, depending on the selected position)
  9. With the DIC displaying the correct fob position that is to be programmed, place the new/replacement key fob in the console fob pocket with the buttons facing forward.
  10. A beep will occur once the fob has been learned.
  11. If programming additional key fobs and there is no DIC prompt that indicates READY FOR FOB X, repeat steps 7 and 8.
  12. Exit programming mode by pushing the OFF/ACC portion of the ignition switch. Note: Failure to exit programming mode (press OFF/ACC) prior to pressing the UNLOCK button of each key fob programmed will result in that fob being inoperative. Pressing the UNLOCK button completes the programming sequence and is require to ensure transmitter operation.
  13. Press the UNLOCK button on each key fob that was programmed to finalize the programming and confirm system operation.

Nov 03, 2010 | 2006 Cadillac STS

4 Answers

My 2006 cadillac sts key fob all of a sudden is not working it says no fob detected and i have the fob what can b wrong??


Some late model fobs contain electronics beyond the push buttons.
Batteries are replaceable...small screws may let you do this.
If the battery is not the cause....a replacement fob may be expensive. A road service technician can probably troubleshoot and replace cheaper than dealer !

Sep 07, 2010 | 2006 Cadillac STS

1 Answer

Programming a keyless entry remote


Key Fob Auto Learn
This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming. 

The vehicle must be OFF. 
Place the replacement key fob in the console pocket with the buttons facing forward. 
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. 

The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. 
When the counter reaches 0, DIC will display OFF/ACC TO LEARN. 
Repeat steps 5-7 two more times, for a total of 30 minutes. 
The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2. 
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. 
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode. 
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. 

Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac. 

Jul 01, 2009 | 2003 Cadillac Deville

4 Answers

2003 Jaguar S-Type, programming a key fob


The switchblade key would need to be compatable with your ignition switch barrel. Only normally available from jag dealers who check the Jag owners register before supplying you a replacement.
The older type seperate fobs could be programmed by switching the ignition on and off 8 times (allowing all functions to settle) and on the 9th switch on - press a button on each fob and then switch off. to test use a good fob to lock the car then try the reprogammed fob to unlock/lock. Sometimes this works first time - sometimes needs a couple of tries.

Mar 21, 2009 | 2003 Jaguar S-Type

Not finding what you are looking for?
2003 Jaguar X-Type Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...