Question about Saturn Cars & Trucks

Open Question

Code p0117 engine coolant tempature sensor-circuit low input

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Molson02536
  • 3854 Answers

SOURCE: 1998 PONTIAC SUNFIRE ADVISE

Exhaust Gas Recirculation System Is the main problem here. the other code P0118 may be a bad temprature sensor or your thermostate needs to be changed. Last it could be a weak water pump. 

So what is an EGR system and how does it work? EGR stands for Exhaust Gas Recirculation, and as its name implies, this system allows exhaust gasses from your car to be re-circulated into the engine, helping to reduce emissions. These systems are mostly comprised of the EGR valve, a DPFE (Delta Pressure Feedback EGR) sensor, hoses, a vacuum regulator, some vacuum lines, wiring, the computer and the exhaust tube leading to the valve itself. 
The car's wiring can be tested in the normal fashion by looking for broken and lose wire, and all vacuum lines can be checked easily for cracks, leaks and correct routing.
The last thing i would then check is the the EGR valve, EGR vacuum regulator and DPFE sensor (or similar flow sensor).
I hope this helps and good luck

Posted on Apr 09, 2009

Ad
  • 4088 Answers

SOURCE: I have a 1996 Mazda 626, the check engine light

The cooling fan must run or the car must be running into the wind to keep from cooking the engine. Physically turn the fan to see if it turns freely (cold engine). The computer reads coolant temperature and trips the fan relay on when normal temperature is reached. You need to read the control voltage at the relay to determine the problem. Possible bad temp sensor.

Posted on Jul 15, 2009

kapishtech
  • 2272 Answers

SOURCE: 2003 kia sorento problems :

For error code p0117: Check the coolant reservoir tank.When you first start up your car the engine and radiator are cut off from the coolant reservoir. As the engine heats up so does the coolant, the coolant expands. There is a one way valve that allows that expanding coolant to leave into the reservoir. So basically due to this the coolant tank begins to develop cracks in it, slowly leaking coolant fluid and leading to the engine not being able to cool itself/overheating. ---------------- For error p0306 problem:The problem is related to ignition cylinder injectors.Clean the ignition cylinder and check.If still the same problem then ignition cylinder needs to be replaced. ------------ For error b2500 the problem:-- The components of the supplemental restraint system consist of: Seatbelts; SRS Indicator light; Airbags; Impact sensors.This all has to be checked.------------------- Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Posted on Sep 09, 2010

  • 2428 Answers

SOURCE: engine coolant temp sensor code p0117 but just put

Are you sure you put the right one in There are two different ones One controls the gauge and one control the computer funtions that be the one that has two wires going to it

Posted on Nov 16, 2010

  • 381 Answers

SOURCE: 99 Breeze is running codes I need help on what I

I would replace your cam shaft position sensor. It can cause the car to start hard and run bad if it is bad. Let me know what engine you have and I will be able to tell you where it is located.

Posted on Dec 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which one is the ect sensor on my 2002 ford ranger, 4.0 v6 4x4, and how do I replace it


P0117 - Engine Coolant Temperature (ECT) Circuit Low Input Indicates the sensor signal is less than Self-Test minimum. The ECT sensor minimum is 0.2 volts or 121°C (250°F). Note on some vehicles that are not equipped with an ECT sensor, CHT can be used and can set this DTC.
  • Grounded circuit in harness
  • Damaged sensor
  • Improper harness connection
  • Damaged PCM
ECT V PID reading less than 0.2 volts with key ON and engine OFF or during any engine operating mode indicates a hard fault.

Jun 18, 2016 | Ford Cars & Trucks

1 Answer

Ok 1989 f super duty no start when hot. showing codes 112,117 122 and998


P0112-intake air temperature circuit low input
Possible cause dirty air filter, poor electric connection, faulty sensor

P0117- engine coolant temperature circuit low input
Possible cause faulty sensor, low coolant level, faulty thermostat, poor connection at ect

P022- throttle position sensor/switch "a" circuit low input
Possible cause faulty sensor, poor connection

P0998_ shift solenoid F control circuit low

Oct 05, 2015 | Cars & Trucks

1 Answer

Code active, unplug coolant sensor dash gauge stops reading


What make vehicle ? some vehicles have two coolant sensors . One for temp. gauge an another one for the ECM / PCM input. Do you have a check engine light lit ?

A DTC will be set if an abnormal reading occurs, P0116 for sensor performance, P0117 low input or

P0118 for a high input. The coolant temperature sensor temperature reading should closely match the

air charge/manifold temperature reading on a scan tool if the engine has not been run for over an hour.
The sensor circuit can be checked for proper voltage using a voltmeter.

Jun 03, 2015 | Cars & Trucks

1 Answer

I went to scan my toyota yaris car and the following codes were give ; temperature ckt low input po117


EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Dec 13, 2012 | 2001 Toyota Yaris

1 Answer

Need obd trouble codes & meanings


here r your trouble code meanings:
1) p0123-throttle position sensor circuit, high input.
2)p0117-engine coolant temperature circuit, low input.
3)p0118-engine coolant temperature ciurcuit , high input.

Jun 18, 2012 | 1997 Plymouth Breeze

1 Answer

2001 300m overheating and leaking water got code po117


P0117 Engine Coolant Temperature Circuit Low Input,,,Code P0117 indicates a low voltage input from the Coolant Temperature Sensor to the PCM. don't assume that the sensor is bad in this case, often it can be as simple as Rusty and/or corroded Engine Coolant, also check the connections to be sure they are tight, if these check out, then and only then,, you'll have to change the sensor

Aug 14, 2011 | Chrysler 300M Cars & Trucks

1 Answer

My friends car came up with this code and p0117 and he says when he accelerates it feels like its holding back


The P0117 code would not effect the acceleration of the vehicle. Probably just need a good tune up unless there are other codes showing in the system.

P0117 - Engine Coolant Temperature Circuit Low Input. The engine coolant temperature sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the ECM. The modified signal returns to the ECM as the engine coolant temperature input. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.

Causes:
- Harness or connectors (The sensor circuit is open or shorted.)
- Engine coolant temperature sensor may be faulty
- Low engine coolant level.

Solutions:
- Replaced coolant temperature sensor
- Repair connector or harness

Jan 17, 2011 | Mitsubishi Eclipse Cars & Trucks

1 Answer

2004 vw beetle code p0117 how to fix


P0117 Engine Coolant Temp Sensor Circuit Low Input

ECM detects short circuit in wiring or engine coolant temp sensor (G62)

Feb 22, 2010 | 1998 Volkswagen Jetta

2 Answers

For ''what does obd2 code p0117 on my 2000 crown victoria means''


P0117-Engine Coolant Temperature Circuit Low

Possible Causes:

ECT sensor signal circuit is grounded in the wiring harness ECT sensor is damaged or the PCM has failed

Nov 12, 2009 | 2000 Ford Crown Victoria

2 Answers

I have a 96 eclipse and the check engine and battery light are on, the code it throws is p1493 and p0117 what is wrong with it?


P1493 Battery Temp. Sensor, Low Voltage
P0117 ECT Sensor, Low voltage

Make sure the engine is reaching operating temperature, U may have a problem w/the thermostat, this is code P0117

Have the battery and the Alternator tested for possiable charging system issue, this is code P1493

Oct 14, 2008 | Mitsubishi Eclipse Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...