Question about Nissan Cars & Trucks

Open Question

Nissan cw20 pd6

Clinder head torque and inlet and exhaust settings thank you

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 88 Answers

SOURCE: torque settings 1986 nissan kingcab head

lookdone ahundred of them o never went by book always on a nissan torque to 40 in center stagger pattern then 80 done any trouble while on job let kme know hey if u dont mind vote for me on fixya

Posted on May 24, 2009

Ad
  • 8 Answers

SOURCE: engine head torque settings for 2005 nissan sentra 1.8

email me ill send you it via email cant post here too bigg!!

Posted on May 29, 2009

SOURCE: head bolt torque settings for 720 nissan cab 2

dear friend-your torque setting on the 720 is the same as the L18 and is set at 85 - 90 nm.

Posted on Jul 23, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

ebjebs
  • 197 Answers

SOURCE: head bolt settings

1st - step; - 22 ft./lbs. 2nd - step; - 58 ft./lbs. 3rd - step, loosen all bolts completely; 4th - step; - 22 ft./lbs. 5th - step; - 54 ft./lbs.fig074.png

Posted on Feb 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder Head bolt torque and tappet settings to suit a , Ford Anglia 1964 105E Engine


Hi valve clearance inlet 0.010 in (0.254 mm). Exhaust 0.017 in (0.432 mm) normal running temperature .. Cylinder head bolts Torque 65 - 70 lb/ft.,.. Cheers

Jan 10, 2017 | Ford Cars & Trucks

1 Answer

What is the tappet clearance and torque setting for hyundai atos 1.1 2007


valve clearance is inlet .02mm hot. exhaust .025 mm hot cyl head torque is cyl head torque stage1 30-35nm stage2 60-70nm stage3 run engine for 15 minutes. stage 4 tighten further 70-75 nm

Dec 15, 2016 | 2007 Hyundai Atos 1.1

1 Answer

Nissan extral head valve inlet tight how does


Valve clearance on NISSAN E15 (S) Engine - Nissan Forum

www.nissanforums.com/.../49192-valve-clearance-nissan-e15-s-engine.h...

Mar 3, 2004 - 15 posts - ‎6 authors
Does anybody know what is the valve clearance for inlet and outlet for this type of engine? ... Nissan Xterra Forum · Nissan Armada Forum · Nissan Frontier Forum ·Nissan Titan Forum ..... the head so they don't burn up, especially the exhaust valves.Tight exhaust valves are the #1 reason they burn up.

Nov 28, 2015 | Nissan Cars & Trucks

1 Answer

Torque specifications


Head bolts are torqued in 3 steps, 1-18ft.lbs, 2-60 degrees, 3-60 degrees, camshaft caps-10-11 ftlbs, intake manifold-12-17ftlbs, exh manifolds-32-40 ftlbs, camshaft pulley-74-89 ftlbs.

Feb 05, 2014 | Cars & Trucks

1 Answer

What is the valve clearance and head bolt torque on a nissan td27 engine 1996 model


valve clearance is .014 inch for intake and exhaust with engine warm.
head torque it 21 ftlbs, then 44 ftlbs, then loosen all, torque to 89 inchlbs, then to 21ftlbs, then mark and turn the bolts an additional 60 to 65 degrees.
cyl head sub bolts torque 80 to 100 inchlbs.
thanks.

Jan 13, 2011 | 1990 Nissan Hardbody King Cab

1 Answer

Blown head gaskit need to remove head and replace with new ong


2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Accessory drive belt
    • Air cleaner outlet duct
    • Engine mount
    • Intake manifold
    • Exhaust manifold
    • Engine Coolant Temperature (ECT) sensor electrical connector
    • Power steering pump
    • Radiator inlet pipe
    • Spark plug wires
    • Rocker arm cover

    NOTE Whenever valve train components are removed, keep them in order for installation purposes.

    • Rocker arms and pushrods
    • Lifters
    • Alternator rear brace and the alternator
    • Power steering pump
    • Radiator inlet pipe
    • Ignition coil assembly
    • Accessory bracket
    • Spark plug wires
    • Cylinder head bolts

    WARNING Two sizes of bolts are used; note the location of each.

    • Cylinder head
  5. Inspect the cylinder head and block surface for cracks, nicks, heavy scratches and flatness.
b9d2546.gif
Cylinder head torquing sequence—2.2L (VIN 4) engine

  1. Install or connect the following:
    • Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.
    • Lifters
    • Pushrods and rocker arms. Torque nuts to 22 ft. lbs. (30 Nm).
    • Rocker arm cover. Torque the bolts to 89 inch lbs. (10 Nm).
    • Spark plug wires
    • Accessory bracket
    • Ignition coil assembly
    • Radiator inlet pipe
    • Power steering pump. Torque the bolts to 22 ft. lbs. (30 Nm).
    • ECT sensor electrical connector
    • Exhaust manifold. Torque the nuts to 118 inch lbs. (13 Nm).
    • Alternator. Torque the bolts to 37 ft. lbs. (50 Nm).
    • Intake manifold. Torque the bolts to 17 ft. lbs. (24 Nm).
    • Engine mount. Torque the bolts to 55 ft. lbs. (75 Nm).
    • Air cleaner outlet duct
    • Accessory drive belt
    • Negative battery cable
  2. Refill and bleed the cooling system.
  3. Start the vehicle and inspect for leaks.

Oct 08, 2009 | 2000 Chevrolet Cavalier

1 Answer

Head stud torque


cyl head torqes.1st stage 29 nm. 2 nd stage 57-67 nm. 3rd stage slacken off 360 cegrees, 4th stage 29 nm. 5th stage 64-74 nm. intake and exhaust valve clearance .38 mm hot setting. hope it goes ok.

Aug 14, 2009 | 1987 Nissan King Cab

1 Answer

On my 4 clinders mitsubishi galant 2003 the time belt was broke down for this reason the mecanic send the head engine to the machine shopp for replace some valves after that every 700 miles I have to add...


if there is no blueish smoke from the exhaust then the oil is leaking. if there is, then the engine is burning it. was a new head gasket installed? it should have been. was the head bolts properly torqued to specification. the mating surfaces (head and block) might have been gouged

Jul 28, 2009 | 2003 Mitsubishi Galant

1 Answer

Differential Torque settings for 2003 Town Car


New cylinder head bolts are required and an angle guage,or you can make one up with card and a set square. Head bolt torque is 25Nm(newton metres)+60degrees + 60deg + 60 deg so it's a four step process.Con.rod bolts(big-end)28Nm,Inlet manifold 28Nm,Exhaust manifold 25Nm, Crank pulley 40Nm,Sump 5Nm and use locking compound (loctite)Timing cover 6Nm. Valve clearance,set inlets to .006" and ehausts to .010"(set approx.when cold then re-adjust while warmed engine is idling.

Feb 20, 2009 | 2003 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...