Question about Cars & Trucks

1 Answer

I have a 1980 Winnebago frontier and it was hit by a power surge. Now my level indicator/pump switch panel isn't functioning. I have checked all of the fuses but I can't figure out what's wrong. My pump no longer works at all and none of my indicators work either.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,223 Answers

Test the IC regulator and fix it. This control the power in the panel

God bless youI have a 1980 Winnebago frontier and it was hit by - 66cd4fe3-4113-4ddb-9dd6-87c041b9b2f7.jpg

Posted on Jul 23, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2009 nissan frontier windshield washer pump won't work

Check fuse in fuse box inside vehicle,if good,then go to windshield washer pump and disconnect wiring,get meter and check if power is going to pump,if so then pump is at fault,if no power,thenwiring could be short somewhere to fuse box.Also check your washer hoses,that they are not kinked or came loose.Pump could just be loose.

Jan 04, 2013 | 2009 Nissan Frontier

2 Answers

How to fix 2002 toyota camry hard steering

Check the power steering fluid levels. Also the pump may need replacing if it isn't delivering enough hydraulic pressure to the steering box. Be sure to lube all the steering components on the chassis if possible.

Mar 31, 2012 | 2002 Toyota Camry

1 Answer

Automatic Doors won't function-How do I fix or what could be the problem

The door doesn't open with the remote or the in-car switch? I'd check the fuse, then check for power to the door actuator when the button is pressed. If there is power at the door actuator then I'd suspect a bad actuator motor. If there isn't power, please post back and I'll put my thinking cap on.

Dec 25, 2011 | 2002 Chrysler Town & Country

1 Answer

Neutral safety switch isn't working, may be just a fuse I'm told but don't know where the fuse is to check it. It's a 1998 Nissan Frontier 2WD Pickup with a manual ******. It will push...

Page 169 shows you where the fuse box is located. Check the fuses and if there is one that is blown replace it with the same amp fuse.

Hope this helps.

Sep 06, 2011 | Nissan Frontier Cars & Trucks

2 Answers

On my 99 taurus I have two problems.first the fuel gauge isn't reading accurately,it stayin at 3/8 full.along with that gauge the temp gauge isn't moving it stays at cold.second major problem it...

You might have to get the fuel pump out of the tank and clean the patenchio meter which moves up and down, clean it with an eraser on the end of the pencil for best results.
As for the temp guage, check the temp sensor it might have grounded.
Strange whining could be from the loose belt check tensioner, power steering pump for pressure, sterring rack might be seasing/leaking internally.

Aug 19, 2011 | 1999 Ford Taurus

1 Answer

Where is the rollover switch on the fuel line, and where is it located in a 1990 Plymouth Voyager. Van hasn't been driven in about 6 years. Fuel pump was working ,now it isn't. It is a EFI...

The switch is a check valve. no electrical to it. It is located on top of the tank. Try hitting the bottom of the tank. if the fuel pump starts working then replace the pump.

Jun 16, 2011 | 1990 Plymouth Grand Voyager

1 Answer

I have a 2001 winnebago on a workhorse chasis. with 4L80-e transmission that dont lock when put into park

There is a fuse for the auto park that you need to check and also make sure that the reservoir under the winnebago isn"t leaking. There is a green switch under the motor home on the hydraulic unit for the brake that goes bad quit often.

Sep 23, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

Directions of how to change a power steering pump

  1. Disconnect battery ground cable.
  2. Disconnect inlet and outlet hoses from pump.
  3. Remove serpentine belt guard as necessary.
  4. Remove belt from pulley, using 1/2 inch breaker bar.
  5. Remove coolant recovery bottle as necessary.
  6. Remove pump assembly.
  7. Transfer pulley as necessary.
  8. Reverse procedure to install, them bleed power steering system as follows:
    1. Turn wheels all the way to left.
    2. Add power steering to Cold mark on fluid level indicator.
    3. Start engine and run at fast idle, then add fluid, if necessary, to bring level to Cold mark.
    4. Bleed system by turning wheels from side to side without hitting stops. Keep fluid level at Cold mark.
    5. Return wheels to center position and continue running engine for 2-3 minutes.
    6. Road test vehicle to ensure steering functions normally and is free of noise.
    7. Check fluid level and ensure level is at Hot mark after system has stabilized at its normal operating temperature.

Aug 19, 2010 | 1992 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides