Question about Cars & Trucks

Open Question

Replace clutch master cylinder on Mazda T4100 truck

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 98 Answers

SOURCE: 86 isuzu clutch- master cylinder ran dry

Did you bleed the system? There is probably a bleeder on the slave cylinder and you may need to jemmy the selector fork/ Also look fro a damper valve between the master and slave cylinder... it will need bleeding too.

Posted on Nov 07, 2008

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

  • 6 Answers

SOURCE: stuck clutch pedal on a Mazda B series truck

Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Posted on Dec 14, 2009

  • 20 Answers

SOURCE: My 1989 Ford F150 manual transmission is stuck in

YOU NEED TO PULL THE TRANS AND REPLACE THE SLAVE CYL IF THE FLUID IS LEAKING AT ALL ONE WAY OR THE OTHER YOU WILL END UP REPLACING THE CLUTCH MASTER CYL BUT THIS TIME YOU NEED TO GAIN ACCESS TO THE SLAVE CYL AND APPLY PRESSURE TO IT HOLDING IT BACK WHILE SOMEONE PUMPS THE PEDAL AND YOU BLEED IT WORKS

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the clutch master cyl on my 1984 mazda t4100 truck


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Sep 26, 2016 | Mazda Cars & Trucks

1 Answer

How to replace the clutch master cylinder


It says the brake and clutch master are the same one.here's a link on how to replace. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Here are some new ones to look at. Master Cylinder Brake System at AutoZone com Best Master Cylinder Brake...

Apr 03, 2015 | 1998 Mazda 626

1 Answer

My mazda protege 1997 have a hard clutch to push,is there any solution to make more smooth to push the pedal?


If you have a cable operated clutch then replace the cable as it is binding up inside the case. If you have a hydraulic clutch system the replace the clutch slave cylinder and master cylinder as there is a problem with the rubbers in the units that have expanded from contaminants and are seizing up in the cylinders.

May 26, 2014 | 1997 Mazda Protege

1 Answer

I have a 2000 mazda 323 with a manual transmission. i have already change the clutch kit but the gear is still hard to shift


Check the hydraulic clutch operation. This is a clutch master cylinder with a reservoir on the firewall, and a clutch slave cylinder down on the bell housing of the transmission, with a steel tube running from the master to the slave cylinder. When clutch pedal is depressed, hydraulic fluid (brake fluid) is forced from the master to the slave. The slave cylinder should push out a little plunger that contacts the clutch fork lever-pushing it forward to engage the clutch.
Add brake fluid to the reservoir if needed. Watch the plunger on the slave cylinder: if it moves little, or not enough, try bleeding the slave from the bleeder valve. They are bled just like brakes. If bleeding doesn't help, your clutch master or the slave may need replacing. The master cylinder, like a brake master, has internal seals that hold hydraulic pressure, so force can be applied to the plunger on the slave cylinder.

Dec 09, 2013 | Mazda 323 Cars & Trucks

2 Answers

How do I bleed a clutch for a 1985 mazda rx-7


Your clutch slave cylinder could be bad and leaking,here's a picture of it,it's bolted to the side of transmission,has a bleeder screw on it for bleeding.Normally,your fluid shouldn't be low,here's how to replace.

Jan 30, 2013 | 1985 Mazda RX-7

1 Answer

Clutch piston too short?


sounds more like a seal to me

Sep 16, 2012 | 1997 Mazda MX-5 Miata

2 Answers

Well I fitted a clutch in my t4100 Mazda truck all ok but I can hear a squiling nose coming out near the clutch what might that be ?????


ok new clutch. did you replace the throw out bearing? what about the pilot bearing,replace that too?these are the main squealers in clutches. if you push in on the clutch w/engine running does the squeal stop?[if so i suspect throw out bearing] if it squeals either w/clutch in or out,i suspect pilot bearing. hope this helps and thank you for choosing fixya.com if you need further assistance,please repost your question to fixya.com

Jan 22, 2011 | 2007 Mazda B4000

2 Answers

Problems shifting, clutch feels fine.


Most likely the master cylinder. Both usually need replaced together. If one fails the other will most likely soon after. Then bleed system again.

May 23, 2010 | 1997 Mazda MX-6

1 Answer

How do you replace a clutch bearing pressure plate? On a 1992 mazda navajo


You need to remove the transmission (and transfer case if its 4 wheel or all wheel drive) to access the clutch assembly. Be prepared to replace the clutch disk, pressure plate, thrust bearing, throwout bearing, and in your case since its a Ford/Mazda the slave cylinder and plastic line to the master cylinder. A very big job for the do-it-yourself-er.

Jan 11, 2010 | 1992 Mazda Navajo

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...