Question about Cars & Trucks

Open Question

2008 dodge ram 2500 6.7L diesel turbo boost control sensor location?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 29 Answers

SOURCE: Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel

I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Posted on May 03, 2009

  • 66 Answers

SOURCE: I am looking for the I.A.T. Sensor location on my truck

If your looking for the Intake Air Temp/Manifold Absolute Pressure sensor (IAT/MAP)(2003 model year and up) It is on the top of the intake manifold, just to the left of the #3 injector fuel line. There are 2 small Torx screws holding it.

Posted on May 27, 2009

  • 1 Answer

SOURCE: problem with hid on 2008 dodge ram 2500

Not too much amperage. HID lights use less amps. Duh. The circuit is showing a failure in the HID kit from not enough amps so it turns off. You need to add a resistor.

Posted on Dec 07, 2009

  • 31 Answers

SOURCE: Serpentine belt replacement for a 2004 Dodge 3500

check the hood or the frame rail around the engine bay. there should be a diagram.

Posted on Feb 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ihave error code p0299


The boost pressure is lower than the expected boost pressure based on engine operating conditions is why the code set ... Mos tlikely cause i sone or more of the following, Intake air system restriction, Turbo charger damaged, Intake air system leak, Boost pressure sensor ... check for leaks first they really mess with a diesel engine and will be your cheapest repair .... hope I helped !!

Mar 29, 2012 | 2005 Dodge Ram 2500 Truck

1 Answer

What dose the crank sensor control in a 96 dodge diesel


The crank sensor on the truck works with the camsensor the crank sensor uses the cam to synchronize and identify where number one piston position is at. It is responsible to fire you injector and for how long is determined by the cam position sensor. On a 96 Dodge diesel the crank sensor is also responsible for you tach reading,your air condition ,and for the alternator.

Mar 06, 2012 | 2008 Dodge Ram Pickup 2500

1 Answer

Where is the cam sensor on a 1999 dodge ram 4x4 turbo diesel located


cansmo_123.gifIt is located below the fuel injection pump attached to the timing gear cover

Aug 28, 2011 | 1999 Dodge Ram 2500 4WD

1 Answer

I have the following fault codes reading


P0216 - injector timing control circuit

P0234 - turbo / supercharger over boost condition

P0523 - engine oil pressure sensor / switch circuit high inout.

Jan 22, 2010 | 1998 Dodge Ram 3500 2WD

1 Answer

Lack of boost pressure


There is a reset on the turbo you can press that might do it it's a yellow buttion I believe but you should take it to the auto parts store and get the to read the codes in the computer

Sep 28, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

2001 dodge ram 2500 diesel with 6spd manual trans. showing fault codes p1698 , p0237 & p0562. the truck will crank but not start. it has two new battery & map sensor.


p0562 is System voltage low
p0237 is Turbo/supercharger boost sensor A circuit low

cannot find a code p1698 but did find a p0698
p0698 is Accelerator pedal position sensor supply voltage to low

Apr 13, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

I am looking for the I.A.T. Sensor location on my truck


If your looking for the Intake Air Temp/Manifold Absolute Pressure sensor (IAT/MAP)(2003 model year and up) It is on the top of the intake manifold, just to the left of the #3 injector fuel line. There are 2 small Torx screws holding it.

Apr 05, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

RPM Oscillating


have you had the vehicle speed control reprogrammed if not that could be your problem

Jun 26, 2008 | 2005 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...