Question about Cars & Trucks

Open Question

Remove ignition housing cylinder saturn 2000 - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
onyxvu
  • 74 Answers

SOURCE: 2002 S series Saturn remove and replace ignition cylinder

unfortunately your cylinder's guts exploded in the cylinder housing and you will need to replace both now

Posted on May 26, 2009

Ad
jeffbvegas1
  • 520 Answers

SOURCE: Saturn Ion 3 Ignition Cylinder Lock

Im thinking your going to be ok as far as warranty repair,if your dealers service dept is insensitive, call Saturn assist @ 1.800.553.6000 On to the ignition switch ....separate colum halves with #2 screwdriver> access ignition housing and look for trip slot on top side of cylinder>use pocket size screwdriver to trip button in slot while in ACC position and pull out...good luck

Posted on Jul 20, 2009

techbuster
  • 5081 Answers

SOURCE: How do I remove the ignition lock cylinder from a

REMOVAL

  1. Disable SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".
  2. Disconnect negative battery cable.
  3. Remove lock cylinder bezel from steering column shroud by carefully prying with thin blade screwdriver.
  4. Remove shroud fasteners and remove steering column upper and lower shroud panels.
  5. Insert key into ignition lock cylinder and rotate to RUN position. Then rotate ignition cylinder back to ACC position.
  6. Depress locking button on side of ignition module assembly with a thin pick-type tool. Slide lock cylinder assembly from ignition module.
INSTALLATION

IMPORTANT: Actuator blade within ignition module housing must be in ACC position to install lock cylinder assembly. If rotated, replace it to ACC position, using needle nose pliers.

  1. Insert key into ignition lock cylinder and install into ignition module.
  2. Install steering column upper and lower shrouds and shroud fasteners.
  3. Install lock cylinder bezel.
  4. Connect negative battery cable.
  5. Enable the SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".

Posted on Apr 07, 2010

Testimonial: "Great information! Thanks for the help. Now I can get the ignition rekeyed to match the doors after the dealer changed the switch."

BCAS1298
  • 3092 Answers

SOURCE: Trying to find where the

Your 6 cylinder 3.0 L has two ignition control module's, the module are part of the ignition coil assembly, there's a right and left bank, hope this was very helpful.

Posted on Aug 20, 2010

  • 3911 Answers

SOURCE: on a 2000 sw saturn station magon, regardless of

go to www.youtube.com and search for "saturn" "lock cylinder" "ignition" I know there is at least one video showing someone removing the lock cylinder. you can watch it and do the same if you wish.

Posted on Mar 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i install tumblers in my new ignition switch in my 2001 saturn ls2


unless ur a locksmith changing the tumblers is extremely hard .if you want to change the ignition cylinder you need to to check your key if the key is electronic need dealer to flash new ignition cylinder for car,if non electric u can look for one at a bone yard ,on line ,or dealer --to remove remove the plastic housing around steering column disconnect wires and unscrew the cylinder from column

Aug 15, 2013 | Saturn L-Series Cars & Trucks

1 Answer

Need to remove ignition lock. there is always a trick to doing this. what is the procedure? i have a 2001 saturn sc2.


There are several procedures in the manual--I think for different models. I think I picked the one for S-series, but let me know if this doesn't look right.

  1. Disconnect the negative battery cable.
  2. Disable the SIR system.
  3. Remove the steering column trim covers.
  4. Turn the ignition lock cylinder to the RUN position.
    NOTE There are two retainers on the ignition lock cylinder. Depress both retainers to remove the lock cylinder from the housing.
    jturcotte_1869.gif

    Fig. Depress the first retainer through the lock housing access hole (2) and depress the second retainer through the lock housing access hole (1)

  5. Depress the first retainer through the lock housing access hole with a small allen wrench or similar pick-type tool. The lock cylinder will back out slightly.
  6. Depress the second retainer through the lock housing access hole. The lock cylinder will back out slightly again.
  7. Pull the lock cylinder out enough to locate the second retainer to the lock housing access hole.
  8. Depress the retainer though the access hole a second time. The ignition cylinder should release from the housing. If not, the ignition cylinder may need to be moved in and out several times to locate the retainer correctly in the hole.
  9. Remove the lock cylinder from the lock housing.

To install:
  1. Position the lock cylinder in the run position. Insert the cylinder into the lock housing.
  2. Rotate the lock cylinder in the housing. Verify proper rotation.
  3. Install the steering column trim covers.
  4. Enable the SIR system.
  5. Connect the negative battery cable.

Jun 22, 2011 | 2001 Saturn SC

1 Answer

MY IGNITION CYLINDER ON MY 2000 SATURN LW1 LOCKED UP AND HAD TO PURCHASE A NEW ONE. HOW DO YOU GET THE OLD CYLINDER OUT


You will have to remove all the cowlings from the steering column to access the ignition lock and switch. With the correct key inserted and selected to, probably, the ACC position, you should be able to push on either a pin or a tongue that protrudes from the switch into the housing and the pull the whole lock/switch mechanism out.

Jun 09, 2011 | 2000 Saturn LW

1 Answer

On a 2000 sw saturn station magon, regardless of all the remedies tried the ignition key does not turn in the ignition. how is the cylinder removed in light of this problem? is it possible to drill the key...


go to www.youtube.com and search for "saturn" "lock cylinder" "ignition" I know there is at least one video showing someone removing the lock cylinder. you can watch it and do the same if you wish.

Mar 29, 2011 | 2000 Saturn SW2

1 Answer

Trying remove the ignition in toyota avalon 2000


TO REMOVE THE IGNITION SWITCH FIRST TURN OFF RADIO.AND DISABLE AIRBAGS BY DISCONNECTING NEGATIVE BATTERY CABLE WAITING 20 MINUTES UNTIL AIRBAGS DISCHARGE.TO REMOVE IGNITION SWITCH PLACE THE IGNITION KEY IN THE ACC POSITION. REMOVE THE STEERING WHEEL AND REMOVE THE STEERING COLUMN COVERS.DISCONNECT THE IGNTION SWITCH ELECTRICAL CONNECTORS.REMOVE THE SWITCH RETAINING SCREWS THEN PULL THE SWITCH FROM THE LOCK CYLINDER HOUSING.IF YOU TRYING TO REMOVE THE LOCK CYLINDER WITH LOCK CYLINDER IN ACC POSITION. USE A SMALL SCREW DRIVER OR PUNCH. DEPRESS THE LOCK CYLINDER RETAINING PIN THEN REMOVE LOCK CYLINDER. TO INSTALL NEW LOCK CYLINDER. DEPRESS THE RETAINING PIN AND GUIDE THE LOCK CYLINDER INTO THE HOUSING UNTIL THE RETAINING PIN EXTENDS ITSELF BACK INTO THE LOCATING HOLE IN THE HOUSING.

Mar 01, 2011 | 2000 Toyota Avalon

1 Answer

Key can not turn ignition to start car


its common for the ignition lock cylinder or the ignition cylinder housing to fail on 2000-2001 L series saturns. Try using another key to see if that helps.

Dec 23, 2009 | Saturn L300 Cars & Trucks

1 Answer

Saturn Ion 3 ignition cylinder lock. I just went to the store and pulled into the parking lot. I went to turn off my car, and the key would not turn to shut the car off. I had to drive home to I went to...


Im thinking your going to be ok as far as warranty repair,if your dealers service dept is insensitive, call Saturn assist @ 1.800.553.6000 On to the ignition switch ....separate colum halves with #2 screwdriver> access ignition housing and look for trip slot on top side of cylinder>use pocket size screwdriver to trip button in slot while in ACC position and pull out...good luck

Jul 20, 2009 | 2001 Saturn SC

2 Answers

Have 2000 saturn sl1 replace cyl and keys in


try putting the shifter in N and move the pressure off the wheel.

Jun 05, 2009 | 2002 Saturn Sl

1 Answer

2002 S series Saturn remove and replace ignition cylinder


unfortunately your cylinder's guts exploded in the cylinder housing and you will need to replace both now

May 23, 2009 | 2001 Saturn L-Series

2 Answers

2000 Saturn SL2 - replaced ignition then BCM failed. Related?


the problem is not the bcm. the passlock security sensor is in the cylinder and housing, if the cyl and or housing was replaced the system must be relearned. if you replace the bcm you still need to relearn the system or it still will not start.

Dec 30, 2008 | 2000 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...