Question about Cars & Trucks

Open Question

CV joint removal on 98 Sienna passenger side - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
Bloomingidoi
  • 49 Answers

SOURCE: cv joints

Jack up car, remove tire, caliper, axle nut and washer. remove and seperate tie rod from spindle and remove lower ball joint nut and separate, pull spindle apart from axle, use a pry bar and pop the other end of axle from trans axle housing. think backwards to reassemble.

Posted on Nov 29, 2008

Ad
  • 83 Answers

SOURCE: 97 toyota celica outer cv boot replacement passenger side

have you undone the main hub bolt, if yes, there could be two different items holding the cv joint on, one is a small circlip in the joint end, or the other is just like an expanding metal ring again only small. what i had to do to change my one was take the driveshaft out (easier to see whats there) then gently (rubber hammer) hit the CV joint it should then fall off to allow you to change the CV joint. I spent over an hour trying to get the metal ring off, then after taking driveshaft off it was changed and back on in ten mins. Or you can go to a motor factors or similar and get a boot puller, my opinion hammer works better lol

Posted on Jan 25, 2009

  • 6982 Answers

SOURCE: 1998 grand cherakee driver side cv joint removal

You can find instructions for doing this in any half decent manual. One thing they usually don't tell you is when removing the large axle nut on the end, it helps to put a spare tire on with no center cap and with the vehicle on the ground, break that nut free before starting the job. without air tools, it's next to impossible to remove it when jacked up.

Posted on Mar 10, 2009

  • 52 Answers

SOURCE: need instructions to replace front passengers side

Do yourself a favor and replace the whole cv shaft. Quicker, eaiser and not much money. First get the car in the air and remove the wheel. Then pop the lower ball joint. This is done by unbolting it from the knuckle and using a ball joint seperator fork and a hammer. Then remove the spindle nut on the end of the cv shaft. You push down on the lower A arm pulling the ball joint out of the knuckle and push the cv shaft out of the hub. Once these are dislogged, you can movel the strut and hub out of the way and pull the cv shalt out of the trans axle. Push the new one in and reverse what you did.

Posted on Aug 09, 2009

germcelchar
  • 389 Answers

SOURCE: how do i remove cv axle for a 98 isuzu trooper

Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace passenger side cv joint


remove the axle from the car and use the services of a cv joint reconditioner shop

Oct 26, 2015 | 2008 Ford Fusion 3.0

1 Answer

How do you remove the passenger side cv axle from a '97 dodge avenger?


You will have to replace the ball joint obviously, but go to Youtube and look for a video showing how to replace all of it. That would be your best way to go with a video showing you all the detail

Jul 25, 2014 | 1997 Dodge Avenger

1 Answer

Cv joint on 98 vr4 galant wont come off


Use a prybar to remove the CV joint, place against hosing and gently pry to release CV.
This is assuming you have un bolted the necessary front end parts prior to removing the CV joint.

Jan 21, 2013 | Mitsubishi Cars & Trucks

1 Answer

2001 toyota sienna changed drive shaft & ABS lights on now


Sounds like the ABS sensor is not hooked up.
The sensor is behind the brake rotor attached to the spindle where the axle shaft sticks thru.
You might want to have the computer scanned for codes to make sure the light is on for the same wheel the axle was removed from.

Jul 17, 2012 | 2001 Toyota Sienna

1 Answer

How do you remove right side cv joint out. do u remove motor mount . the bering has made luv and married the motor mount and will not let go.


there may be a snap ring holding it in, or you just might have to unbolt it and take out the mount.

Sep 06, 2010 | 1998 Toyota Sienna

1 Answer

Pass cv joint will not come out of carier, removed clip, what next ? 97 toyota avalon...


This is for the removal of the passenger side cv joint. If the Avalon carrier is like the Camry you will have to remove the snap ring and the set bolt. You have 2 choices to get the carrier bearing out,(1) remove bracket, and take it out with the cv joint as yiu noticed the bolts are in tight spot (2) You will need a torch with a rose bud tip and put a lot of heat (red hot)on the cast iron bracket and be in postion to hit the cv joint bearing (on the tire side of carrier) with a hammer and drive it out. This is the way I prefer but, take caution with flame. Do step 2 only if you are planning on replacing the cv joint anyway.

Jul 17, 2010 | 1997 Toyota Avalon

1 Answer

Describe your replace front passenger side cv joint 1998 4wd chevy silverado 1500 Problem my front passenger side cv joint is making extremely loud noise, especially while turning. How much can I expect...


CV halfshaft will run you $75 at local autoparts store. Shop labor varies from shop to shop as well as their expertise.
The brake caliper has to be pulled, lower shock bolt removed, upper and lower ball joint seperated (book will say only one but it is not true) and steering knuckle and axle nut removed. CV joint simply unbolts at differential output flange.

Apr 19, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

CV Joint on Passenger side is going


Nedle nose pliers or O ring pliers do remove CV joint

Dec 31, 2009 | 1998 Ford Windstar

1 Answer

Need instructions to replace front passengers side cv joint


Do yourself a favor and replace the whole cv shaft. Quicker, eaiser and not much money. First get the car in the air and remove the wheel. Then pop the lower ball joint. This is done by unbolting it from the knuckle and using a ball joint seperator fork and a hammer. Then remove the spindle nut on the end of the cv shaft. You push down on the lower A arm pulling the ball joint out of the knuckle and push the cv shaft out of the hub. Once these are dislogged, you can movel the strut and hub out of the way and pull the cv shalt out of the trans axle. Push the new one in and reverse what you did.

Aug 08, 2009 | 1996 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13723 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...