Question about Cars & Trucks

Open Question

Hyundai hd65 brake system

Bleeding system for Hd65 2009.model

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause there to be no brakes what so ever even after replacing all the broken brake lines and bleeding them all on a 2003 Hyundai elantra?


if this has anti-lock brakes it may be the HCU(hydraulic control unit) may have air in it. it may have to be activated to get all the air out.

Aug 27, 2015 | 2003 Hyundai Elantra

2 Answers

What order do you bleed a 2005 Hyundai elantras brakes start to finish to remove air?


Same as the last 100 years on any vehicle

Start at the farthest point-- back right,left rear,
right front, left front

Every 2 years your flush all vehicles all brakes

Mar 03, 2013 | Cars & Trucks

1 Answer

Hyundai grace front brakes stucking what is the solution.


you mite have contominated brake fluid and master cilinder thats what it sounds like try flushing brake sistem need more help let me know

Nov 27, 2012 | Cars & Trucks

1 Answer

2006 HYUNDAI Sonata I figured I'd bleed the the rear brakes after replacing the rotors and pads. 120,000 Miles with no previous brake issues besides normal replacement of front rotors and pads. After...


Try re-bleeding ALL wheels starting with furthest away - pass rear, then driv rear, then pass front and driv front. That should get your pedal back. To reset light you need ABS reset tool and it's EXPENSIVE. Have a good competent shop reset it for you. Body shops can reset them also.

Feb 27, 2011 | 2006 Hyundai Sonata

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Cross diagonal braking system on a 01' Accent, after changing out both rear wheel brake cylinders, brake master cylinder and bleeding brakes three times and the following issue has come about since, the...


if your vehicle has anti lock braking you may need to get the air out of the pistons. make the anti lock brakes work (this can be done on gravel relatively easily) then bleed the system one more time.

Oct 17, 2010 | 2001 Hyundai Accent

2 Answers

Brakes won't bleed?


if this has ABS then u need a special tool to bleed the brakes, the dealer has this tool. The dealer will charge about $50 to do this job

Jan 04, 2010 | 2002 Hyundai Santa Fe

1 Answer

How do i bleed the brakes on a hyundai excel 1995 no fluid getting to rear brakes


log on to youtube type in(BLEEDING BRAKES)and it's there step by step.

Oct 02, 2009 | 1994 Hyundai Excel

1 Answer

Can't get the brakes to bleed to a 2006 hyundai tiburon


The tiburon's brakes are simple, there's no special technique to bleeding them. Are you sure you're bleeding them correctly?

If you are bleeding them correctly, then it's possible that you have a brake leek, causing air to get into the system.

Apr 03, 2009 | 2006 Hyundai Tiburon

1 Answer

Dried out brake system, air in brake line


How are you bleeding the brakes? With somebody in the car ot with the tool?

Feb 10, 2009 | 2002 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...