Question about Cars & Trucks

1 Answer

Can anyone tell me what a P246C DTC is on an 08 F250 SD with 6.4 diesel motor. And easiest fix? Thanks

Posted by on

Ad

1 Answer

Any and almost all Codes are found by using Google
Just type in OBD & the code
If it is a manufacture code,some will only be avail
through the use of professional scan tool & software,
& most likely in Enhanced Mode
The Manufacture doesn't have to release those
codes as Generic to the public but they do have
to be avail to use a scan tool
On looking up some codes & the trouble charts
you may need factory manuals,but usually you can find
code on the internet,you just won't know how to diagnose
it without reference charts in some cases.
The easy,quick,cheap really doesn't apply to working
on vehicles
As you know they are very hard to work on or get to anything
& the technology requires the Emission & Diagnostic Manuals
to even know how the systems work

Posted on Jul 22, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: code u0073 on an 08 f250 diesel how can I fix

this dtc is set when the controller area network (can) between the powertrain control module (pcm) and datalink connector (dlc) is open i don't think this is your problem if it is a no start and your truck has less than 100,000 miles on this should be cover under your powertrain warranty unless you have a programmer on this truck your dealer may not repair under warranty

Posted on Apr 19, 2012

melvi_99
  • 387 Answers

SOURCE: I cleared the three DTC codes previous asked,

P1000- on-board dianostic systems readiness test not complete, 1. obd monitors and drive cycle incomplete 2.keep alive memory(KAM) cleared, wat to do and try. remove power take off fuse(PTO) then cleared the code,disconnect pcm connector and visually check for corrosion

Posted on Jun 21, 2010

elkoolarrow
  • 156 Answers

SOURCE: 08 f250 diesel 4wd heater works for a while then

your problem seems to be associated with the temperature control section of your H.V.A.C.(heater ventilation & air condition) system. most likely the electrical motor temperature control actuator. it is located on the right side (passenger), next to the glove compartment, on the upper side. it is hard to see and even alot harder to replace

Posted on Feb 10, 2011

stevenhurc
  • 450 Answers

SOURCE: Isuzu Trooper Diesel DTC problem

bridge pins 5 & 6 in DLC connector
turn ignition to on position
count flashes from check engine light
connector behind front centre console right side

b68a5c1.jpg

Posted on Jul 29, 2009

  • 1 Answer

SOURCE: 2008 Ford F250 6.4 turbo diesel, have 3 DTC codes

SUPERSHIPS PROGRAMMER GIVEN ME LOTS OF CODES AND WILL NOT ALLOW MY TRUCK TO STARTiT TURNS OVER BUT CHOKES ITSELF OFF ONE CODE IS P2291

Posted on Aug 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is TSB 7/2006


TSB 7/2006
Subject/Concern: Hesitations; Poor or no start; Deteriorated fuel economy; Diagnostic trouble codes (DTC) P1412, P0490 and P1335 stored
Model: Focus C-MAX 2003.75 (06/2003?¿½) Build Date: 14.02.2004-01.03.2006
Build Code: 4R-6S
Assembly Plant: Saarlouis
Engine: 2.0L Duratorq-TDCi (DW) Diesel
Focus 2004.75 (07/2004?¿½) Build Date: Up to 01.03.2006
Build Code: Up to 6S
Assembly Plant: Saarlouis
Assembly Plant: Valencia
Engine: 2.0L Duratorq-TDCi (DW) Diesel
Markets: All
Section: 303-08
Summary


Should a customer express concern about one of the following:


* hesitations,
* poor or no start,
* deteriorated fuel economy,
and upon investigation diagnostic trouble codes (DTC) P1412, P0490 and P1335 are stored in the powertrain control module (PCM), the probable cause is a sticky exhaust gas recirculation (EGR) valve.


To rectify this concern, a new EGR valve with a stronger EGR valve motor and revised PCM calibration should be installed.

Jun 23, 2014 | 2003 Ford Focus

1 Answer

Code u0073 on an 08 f250 diesel how can I fix


this dtc is set when the controller area network (can) between the powertrain control module (pcm) and datalink connector (dlc) is open i don't think this is your problem if it is a no start and your truck has less than 100,000 miles on this should be cover under your powertrain warranty unless you have a programmer on this truck your dealer may not repair under warranty

Apr 19, 2012 | Ford F-250 Cars & Trucks

1 Answer

I cleared the three DTC codes previous asked, which were P0088, P0087,nad P2291, re-started the engine and getting a DTC Code P1000 can you tell me what this code is. The three previous codes started when...


P1000- on-board dianostic systems readiness test not complete, 1. obd monitors and drive cycle incomplete 2.keep alive memory(KAM) cleared, wat to do and try. remove power take off fuse(PTO) then cleared the code,disconnect pcm connector and visually check for corrosion

Jun 21, 2010 | 2008 Ford F 250 Super Duty 4WD

4 Answers

2008 Ford F250 6.4 turbo diesel, have 3 DTC codes


P0087- low pressure fuel system. Fuel pressur valve stock open, Fuel volume control valve stuck close, Leaking fuel injector,P0088- fuel pressure contorl valve stuck close, Fuel rail pressure sensor P2291-all @ at the above, means to say poor fuel quality

Jun 21, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

My f250 diesel truck air conditioner does not


check your vacuum storage unit or vaccum pump supply, remember diesel motors dont make vacuum like internal combustion gas powered engines do.. they have an auxilary vacuum motor and resovior to store vacuum to eliminate a lag time in vacuum supply...please rate my help..thanks...

Aug 06, 2009 | 1996 Ford F250 Crew Cab

4 Answers

1999 F250 SD 7.3L cold starting problem


Yes, my 2003 did the same with about 75k miles on it, stranded me on days it stayed under 40F unless I plugged in the block heater the night before, then it started like a champ. Dealer replaced the relay and a control unit under ESP warranty. There's no way to fix this one without throwing parts at it.

Nov 14, 2008 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

Isuzu Trooper Diesel DTC problem


bridge pins 5 & 6 in DLC connector
turn ignition to on position
count flashes from check engine light
connector behind front centre console right side

b68a5c1.jpg

Sep 25, 2008 | 1999 Isuzu Trooper

1 Answer

Looking for a wiring diagram for a 1999 Ford F350 Diesel. Anyone got one???


1999 ford f250 diesel electrical system diagram free|Free eBook ... The 1999 ford f250 diesel electrical system diagram free Documents at ... That's a Ford Tractors wiring diagrams and Harnesses contributed by Neil Reitmeyer ...
www.ebooksquad.com/search/1999+ford+f250+diesel+electrical+system+diagram+free - 22k

Aug 10, 2008 | 1994 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...