Question about Cars & Trucks

1 Answer

How to fit electric window motor - Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 54 Answers

I think you meant fix, and the only fix I know is to go and get one out of a junk yard or buy one from a parts place. There are many numbers on the motor, look for them. Take the motor out if possible and that way you can match it up. Most get worn out from use or water. They have a field like a starter, and that is hard to fix. If you do mean fit, only the original or sister car's will fit in that space to allow clearance for the window guide. Hope that helps.

Posted on Jul 22, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace window motors?


did you have your switches checked 1st? they may be the fault which is a lot easier to repair than stripping your door down just to find out is was the switch;
I did an electric window repair recently and found that the drive gear and track that runs on it just needed lubricating as they had become dry over the years as they do not get serviced.
To remove the motor you will need to remove the interior door trim and plastic weather seal behind it to gain access to the inside of the door.
some of the electric window mechanisms are pop riveted to the door panel which you will have to drill out the pop rivets and replace them with new ones when you are fitting it all back in the door.
Some electric widows run on a cable setup which you will have to replace the whole setup as a unit.

Jul 22, 2014 | 1991 Ford LTD Crown Victoria

2 Answers

1988 mustang passenger window stopped working.driver side works.press button motor silent.locks still work.what could it be? fuse?


Oh! Its 1988!!
  • Check whether the fuse is blown in the fuse box
  • Probably the motor is dead
  • Open the door panel
  • Buy a motor depending on the model
  • Fit it yourself
  • good luck

Sep 23, 2011 | 1988 Ford Mustang

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

What amp altanator does does 2.0 gas motor have?


It depends more on the electrical demands on your car i.e. electric windows etc than engine size but most modern cars have between an 90 and 130 amp alternator fitted, the ampage is usually written on the manufacturers sticker on the alternator also.

Hope this helps

John

Dec 02, 2010 | 2000 Volkswagen Beetle

1 Answer

Rear electric window will notwork


Yes . Remove door panel, switch connectors and plastic protective covering on the door. have a helper pull the windw up while you measure the distance from bottom of window regulator to bottom of door panel.
(approx 8-12"), cut a block of wood that will fit between the bottom of the regulator to bottom of door panel wedge it threw the opening in the door a place it between the regulator and door bottom. Wood is soft and sturdy and should hold up until you get the window fixed.
Can the driver control panel switch make that window work. If the answer is No then the problem is the motor on that side. If the answer is yes then the problem is the switch on that window. by the way if the driver control panel gets the window to rise Merry Christmas you don't need the wooden block.

May 05, 2010 | 1997 Plymouth Grand Voyager

1 Answer

The drivers window of my 2006 suzuki swift has stopped working,all other electrics are ok I'm told the motor need replacing why would this fail the car has only done 13000 miles


Hi most likely it has not failed with them miles on the car.

Take the inner door trim off and have a look around the motor ensure the plug is connected correctly to the motor, and that no wires are contacting the car body.

Also where the door opens and closes the door jam has wires running from the door to the inside of the car door look and check they have not been damaged.

Finally the electric window switch could be at fault pop it out and turn it over make sure all wires are correct and fitted right.
Regards

Dan

Feb 01, 2010 | 2006 Suzuki Swift

1 Answer

My drivers side electric window isnt working mr2


This should help you out for now. Also the BGB is there for future reference. www.mr2-tech.com/bgb/mechanical/volume2/body_electrical_system/Manual_1325_0001.jpg Good luck!
If you find its not the relay and its a motor let me know....keep me posted.

Nov 24, 2009 | 1991 Toyota MR2

1 Answer

Passenger side window motor


Negative. Different Motor all together.

Jun 11, 2009 | Renault Sport Cars & Trucks

1 Answer

WIRING DIAGRAM TO FIT FACTORY ELECTRIC WINDOWS TO AE92 COROLLA


Well black wire should be your earth wire. But are you going from window motor to car or from car to window motor?

Jul 28, 2008 | 1990 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...