Question about Buick Enclave

Open Question

Code u0100 code problem U0100

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

thunderalley
  • 432 Answers

SOURCE: the car stalls intermittently displays codes

Computer

Posted on Oct 03, 2009

adegboyega
  • 158 Answers

SOURCE: what do the code u0100 mean on dodge charger 2006

Hi,


The U0100 code means there is Loss in communication with the ECM/PCM,which might be as a result of one of the following reasons listed below.

1. You had flash downloads applied to your vehicle. Many erroneous DTC codes are generated during flashing and should be cleared after flashing 2. You disconnected/reconnected computers in the car with the power still applied 3. An interruption (break or short) in the CAN network caused communication errors.


a simple software update will help you resolve the issue.




Good luck,

Posted on Aug 28, 2010

  • 1 Answer

SOURCE: Multiple error codes reported: U0100

UO 100-109 typically loss (or near loss) of communications with Onstar. Problem may be loose harness connection or defective onstar backup battery. I'm working on this issue with my 2008 Vue as we speak. I had a very similar code before, last year, and the dealer replaced the battery and the issue was resolved. There does exsist a service dept advisory informing dealers of this Onstar battery issue. Good luck.

Posted on Sep 17, 2010

SOURCE: Im looking for the definition

U0100 - Lost Communication With Engine Control Module (ECM)

Posted on Jan 30, 2011

  • 106 Answers

SOURCE: I had my 2004 Mazda

Codes that begin with the letter U are always communication fault codes between modules in a CAN system. They are basically to be ignored unless a problem is occuring. This is because all of the control modules in your car ( and there are a bunch of them ) are all communicating to each other and sending information between each other on one set of wires called a "twisted pair" Due to the high volume of infomation being sent and received there is the invevitable time when a message will be sent from one module to another and it is lost or not responded to in a timely manner (meaning in milliseconds) When this occurs then a U0100 or other comm fault code is stored.

Posted on May 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble code P0700 & U0100


What make vehicle ? P0700 is a code for transmission problem . U0100 is a problem on the serial data bus or a module on the bus .

Apr 12, 2016 | Cars & Trucks

1 Answer

Toyota codes u0100 and u0101


U0100 means lost of communication with ECM/PCM
U0101 means lost of communication with TCM

Feb 24, 2014 | 2007 Toyota Camry

1 Answer

Toyota vx 200series code u0100


that is a very serious comm problem (Im sad for you, scary code)
reset it and see if it comes back other sysptoms, low battery
just finished jumper cable jump starts, or other odd battery issues???
short answer: take it to Toyota.
long:
U1100 is seatbelt controller
U1110
Lost Communication with Clearance Sonar Module i cant find much on U0100, are you very sure that is it?
DTC U0100 Lost Communication with Engine Control Module (ECM)

1: check all fuses. using and ohm meter (restance low range) for 0 ohms.
2: check battery voltage running engine and not.
12.6v key off, 13.3 to 15v running, if not charge system failure.
3: pull battery minus lug for 1hr. and put back, keep in mind you can lose radio codes. or dead radio for lack of radio pw code.

4: re-seat all CAN buss modules in car, 1 by 1one battery minus pulled.
PCM, BCM , all off them. reseat means pull connector to it and put it back.
It might just be a random glitch, that all comms see, all the time on all networks. Unknown, glitch. (CRC failure)

Jan 31, 2014 | 2004 Toyota Land Cruiser

1 Answer

2006 VW Jetta code U0100


This problem is with ecu / ecm= engine control computer. These are a common and horrible problem on vw's, particularly on tdi's. The signs in a tdi are when car dash lights come on, but no glow plug light,trans gear lights flash, but car still tries to crank. And hopefully ecu has enough power to out out code u0100= no communication with ecu. Unfortunately the ecu will need to be replacd. The ecu is located under the hood, near and under the wipers. Used ecu with same codes run $50-200. New $1000. If get used one make sure has a return policy. codes must match production quarterly year.

Apr 14, 2013 | 2006 Volkswagen Jetta

1 Answer

No start and code u0100


That means that the computer on the car is not working because it cannot communicate with the controller for the transmission.

Feb 07, 2013 | 2006 Saturn ION

1 Answer

Im looking for the definition to code U0100.


U0100 - Lost Communication With Engine Control Module (ECM)

Jan 30, 2011 | Chevrolet Aveo Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...