Question about Cars & Trucks

Open Question

Where are the erls fuse on a Chevy Colorado 2005 and the purge can solenoid? I have a map sensor code and believe these two are tied together

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 51 Answers

SOURCE: 2005 chevy colorado runs rough and gets bad gas mileage.

Sounds like it needs spark plugs and wires, and a fuel system treatment.

Posted on Oct 08, 2008

Ad

SOURCE: purge solenoid location

which vehicle are you actually looking for the purge solenoid on? you have 2 vehicles listed in your question. i'll answer both, lol

the locations are described as if you are looking at the engine from the front of the car with hood open.

on the blazer:

it is located on the left side of the intake manifold just under and behind the throttlebody. it is a canister looking device.

on the silverado:

it is located on the intake manifold on the left side in about the same spot as the blazer. providing the silverado has the 5.3 or 5.7 liter engine. if it also has the 4.3 then obviously it will be the same.

hope this helps!

Posted on Feb 17, 2009

polarcycle
  • 1392 Answers

SOURCE: 2005 chevy colorado abs fault

Sounds like water getting in one of the connectors. You will need to see what fault code is in there when the light comes on, then look at that sensor.

Posted on Jun 05, 2009

c17hydro
  • 2984 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

09 Chevy colorado code p449


PO449-- Evap Vent Valve/Solenoid Circuit Malfunction

PO441--Evap Purge Valve Incorrect Flow
PO 443,444,445 Purge Control Valve Issues


There was no reason to change the gas cap or
purge control valve

Didn't Google the code & use it correctly to diagnose
the problem

Mar 23, 2013 | 2009 Chevrolet Colorado Extended

1 Answer

I have a1997 suburban 5.7 eng. hesitates and backfires on rapid acceleration.


check that your map sensor has direct (unregulated) vacuum. I don't believe that the purge solenoid can create that kind of problem.

Feb 27, 2013 | 1997 Chevrolet Suburban

2 Answers

I have a 2005 chevy colorado. all the lights work except the left rear tail lights. not the bulbs or fuse. help


could be the tail light assy. Chevy had trouble with those in the Trailblazers back in the early 2000's and up.

Nov 26, 2011 | Cars & Trucks

1 Answer

MY 2005 CHEVY COLORADO gave me a code said my solenoid A was bad my problem is which one is A i just need to know which solenoid is A


The code number has to be known There are solenoid for transmission then there is a solenoid for the turbo then there is a camshaft solenoid we need the code it will be P0xx or enhanceddepending on what scan tool you use

May 17, 2011 | 2005 Chevrolet Colorado

1 Answer

The following codes show up on my 2006 chevy colorado PO106 PO116 PO455 PO446 PO496 PO036 PO030


All these codes indicate that maybe you lost your reference signal from the computer. What someone will have to do is check fo voltage and grounds from the PCM on the coolant temp sensor, Both 02 sensor heater circuits, the evap purge solenoid and the gas tank pressure sensor. Its possble the computer failed or you poped a PCM fuse in the fuse box under the hood. The cover should have a legend to tell you which is which but I would pull all of them and inspect anyways.

Apr 20, 2010 | 2006 Chevrolet Colorado

1 Answer

Chevy colorado code 420 and 496 whats the problem?


code 420= Catalyst system efficiency below threshold(bank 1) code 496=Evaporative emission system-high purge flow. Hope this helps if you need more help get back to me Thanks Ray

Feb 15, 2010 | 2005 Chevrolet Colorado

1 Answer

Where is the erls fuse on my 96 chevy cavalier and does that control my 2-3 shift solenoid?


The ERLS fuse does power the solenoid, and the computer grounds it, making it work. Its located in the fuse box. which is on the left end of the dash board.

Nov 20, 2009 | 1996 Chevrolet Cavalier

1 Answer

My 2005 neon failed emissions. It gave me a codes 0441. What excatly does that define?


Trouble Code: P0441 (2.0L L4 VIN C Auto)
EVAP Purge Flow Monitor Fault Print this code dataprint_icon_codes.gif Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
Engine at idle speed in closed loop for 200 seconds, BARO Sensor signal less than 8,000 feet, ECT Sensor more than 160ºF, no Low Fuel, MAP Sensor signal less than 23.7" Hg, and the PCM did not detect any purge flow through the EVAP system during this test.

Possible Causes:
  • EVAP purge solenoid vacuum line loose, leaking or restricted
  • EVAP purge solenoid stuck leaking, stuck open or stuck closed
  • EVAP purge vacuum line to canister leaking or disconnected
  • EVAP canister leaking, damaged or has failed

2005 Dodge Neon - All Configurations - P0441

Nov 01, 2009 | 2005 Dodge Neon

1 Answer

Pulled a code and can't find out what it means


Code 27 and 28 refer to the quad driver circuits in the ecm. These control the grounds for various outputs.
Code 27 is for tcc, canister purge, and egr soleniods. Code 28 refers to fan relay, a/c compressor relay and cruise stepper motor. The canister purge, egr and compressor relay, brake switch and tcc solenoid are all fed by the erls fuse which is probably blown. Check the fuse if it is blown you will have to check these components for a short or a short or open in the wiring. If it is ok check for battery voltage on the pink wire on these solenoids.

Jul 25, 2008 | 1995 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...