Question about 1998 Toyota MARK II

Open Question

Open car remote key eco programming - 1998 Toyota MARK II

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset key fob


Unlock all doors, foot on brake, all doors closed. Cycle key quickly but carefully on-off appr 10 times until the car honks one time.

Do not turn the key far enough to start the car, just to the 'on' position so the dashboard lights up.

When the horn honks, open and close the driver's door, press any remote button and that's it.

Program another remote? Quickly open and close the driver's door again and push a button on the 2nd remote. That's it.

When you're done, remove the key and the horn should honk 3 times. You're all set.
Sometime it takes more than 10 on-offs to set program mode. Open/close the door, lock/unlock etc, wait 10 minutes, then try again

Jul 22, 2014 | Subaru Outback Cars & Trucks

1 Answer

2004 Suzuki Gran Vitara Keyless entry


Try this

2004 XL7

1. Remove key from ignition switch.

2. Close all doors.

3. Open drivers door

4. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

5. Within 20 seconds Close and open drivers door 3 times.

6. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

7. Locks should now lock and unlock automatically to confirm you
have entered programming mode.

8. Press the UNLOCK button on remote and locks should cycle to
confirm programming.

9. Repeat step 8 on each additional remote.

10. Exit vehicle with keys and remote, close door test remote(s)

Jun 01, 2014 | 2007 Suzuki XL-7

1 Answer

How do i program a new keyless remote for my 2002 Suzuki Aerio?


. Remove key from ignition switch.2. Close all doors.
3. Open drivers door
4. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.
5. Within 20 seconds Close and open drivers door 3 times.
6. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.
7. Locks should now lock and unlock automatically to confirm you
have entered programming mode.
8. Press the UNLOCK button on remote and locks should cycle to
confirm programming.
9. Repeat step 8 on each additional remote.
10. Exit vehicle with keys and remote, close door test remote(s).

Jul 13, 2012 | 2002 Suzuki Aerio

1 Answer

How do you program a replacement key for a lexus es 330 2004


Here are the instructions from the factory manual. They must be followed exactly.
2004 ES330
1. Driver's door open, all other doors closed, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.

2. Within 40 seconds:
Close and open driver's door twice.
Insert and remove the key from the ignition switch.

3. Within 40 seconds:
Close and open driver's door twice.
Insert the key into the ignition switch and close the driver's door.

4. Switch ignition ON and OFF:
A. Once to program a key remote transmitter code whilst retaining the original codes.
B. Twice to program a key remote transmitter code whilst erasing the original codes.
C. Three times to check how many key remote transmitters are currently registered.
D. Five times to erase all registered codes.

5. Remove key from ignition switch. System should now lock and unlock vehicle
once, twice or five times depending which mode has been selected. One to four
times, slowly, to indicate number of key remote transmitters registered.

6. Within 40 seconds:
Press and hold LOCK and UNLOCK buttons simultaneously for 1.5 seconds.
Within 3 seconds: Press any key remote transmitter button.

System should now lock and unlock vehicle once to confirm registration or twice
to indicate registration has failed.

7. Within 40 seconds:
To program additional remotes repeat step 60 now on each additional
remote you want programmed.

8. To exit programming mode open driver's door or insert key into ignition.
9. Step out of car with remote(s) in hand and test remote(s).

Nov 01, 2011 | 2004 Lexus ES 330

1 Answer

My cental locking on my focus 2000 reg does not work, i can only open the doors with key individually, also i cannot open my boot from inside, the boot light stays on as well as the light in the car saying...


programming of remote :- ( you will need all your remotes for this )
insert a programmed key into the ignition.
turn key to position 2 & back four times within 6 second.
when you turn the ignition off after the fourth turn you should hear a beep to tell you your in programming mode for the next 10 seconds.
press any button on your new remote ( a tone will be heard when the car accepts the button press ) now do the same with your old remotes too.
either switch the ignition back on or wait until the timer runs out on the programming mode & your done

Dec 23, 2009 | 2000 Ford Focus

3 Answers

Key for my Suzuki Aerio 2003


Don't buy it from the dealer, just buy a used remote from eBay. Use these instructions to program it.

1. Confirm that all doors are closed and the ignition key is out of the ignition cylinder.
2. Open the driver's door.
3. Within 10 seconds, Insert key into ignition turn to ON position and back to OFF and remove the key.
4. Within 20 seconds, close and open the drivers door 3 times. (Drivers door should be open)
5. Within 10 seconds, insert key into ignition turn to ON position and back to OFF and remove the key.
6. Press and hold both the LOCK and UNLOCK buttons together on the same remote for at least 5 seconds, the doors will lock and unlock (that's a very good sign)
7. Within 5 seconds, press the LOCK button on the same remote and release. You just programmed your remote ??
6_23_2017_2_42_10_am.jpg

Apr 22, 2009 | 2003 Suzuki Aerio

2 Answers

I can't lock the car using the remote key. the light flashes on the key but does not lock the doors


try reprograming the remote, if that doesn't work u may need a new remote these are the factory instructions.
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound.
he "Open" button is pressed once for programming the first, or a single,
remote unit.
�� When programming additional remote units for the second, third or fourth
memory addresses, press the "Open" button two, three or four times, in
one-second intervals.
�� Example: press the "Open" button once, wait 1 second, then press once
again to program the second remote unit.
�� After 6 seconds, press "Open" button once to activate the coding ocess.

4. The remote unit will now be coded, and it can be used to unlock the central
locking system. Switch ignition off.

The key must be removed from the ignition before the remote unit can be used to lock
the vehicle.The coding process can be repeated up to 4 times for additional remote units.
In between each remote unit coding, the ignition must be switched off.

Apr 10, 2009 | 2004 Volkswagen Jetta

2 Answers

2001 XJ8 keyless remote programming


This is the procedure from the service manaul:

JAGUAR
XJ8 Remote Control Programming
1. Unlock the Boot/trunk with key.
2. Turn Ignition on.
3. Warning light on dash comes on.
4. When they go out, lift arm rest, inside their is a valley button, Press 5 times within 5 secs of lights on dash going out, Horn & Lights Flash.
5. Press any button on remote, remote programmed.

Jan 16, 2009 | 2006 Jaguar XJ8

1 Answer

Need programming instructions for RKE for 2000 Mazda 626


2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.

Sep 03, 2008 | 2000 Mazda 626

1 Answer

Programming remote to open doors


Dear Customer,

If you didn't change your remote kit than its a best way to take to your dealer ,there is minor problem with sequence so they wil do free of cost with car document.

THNX

May 15, 2008 | 2006 Lexus RX400h Used Cars

Not finding what you are looking for?
1998 Toyota MARK II Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...