Question about Cars & Trucks

Open Question

Engine diagram kia workhorse 2.7

Where is the oil cooler situated in the engine of the kia workhorse

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 52 Answers

SOURCE: need diagram of how to locate on the engine

cooler located on passenger side front. Remove oil filter and find 10-15 10mm bolts. Cooler is sandwiched between filter head plate and the block, two gaskets, not much trouble to fix. Good luck...

Posted on Aug 29, 2009

clifford224
  • 1975 Answers

SOURCE: nissan rogue engine oil cooler

Below is a diagram for you but I was unable to find a part number for you. Hope this helps.

11_17_2011_12_10_56_am.jpg

Posted on Nov 17, 2011

  • 344 Answers

SOURCE: how do you take oil cooler off 99 kia sportage 2.0 engine

Are you shure the filter is not defective?

Posted on Nov 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does engine not turn when turning key of Kia K2700 Workhorse?


possible flat battery.
check the voltage of battery
and tap the starter motor. if it fires up then the starter motor is
not working properly

Aug 09, 2016 | 2007 Kia K2700 Workhorse

1 Answer

How to replace oil; cooler on this year


  • Service and Repair
Oil Cooler Replacement

Removal Procedure

  1. Raise and support the vehicle. Refer to Vehicle Lifting.
  2. Drain the engine oil and remove the oil filter housing.
89116492

  1. Loosen the oil cooler outlet (1) and the inlet (2) lines from the engine block.
  2. Lower the vehicle.
  3. Remove the intake plenum.
  4. Remove the intake manifold.
89116493

  1. Disconnect the following electrical connectors from the water crossover:
    • The engine coolant temperature sender (2)
    • The engine coolant temperature sensor (4)
84936658

  1. Remove the water crossover bolts (1).
  2. Remove the water crossover upper and lower seals (2).
84942881

  1. Loosen the upper heat shield bolts on the left side of the exhaust manifold.
89116496

  1. Remove the oil cooler outlet line from the engine oil cooler.
  2. Remove the oil cooler inlet line from the engine oil cooler.
84942883

  1. Note the positioning of the 4 seals.
84972057

  1. Position the oil feed and return,lines out of the way and secure with mechanic wire.
  2. Remove the engine oil cooler, inlet and outlet nuts (1).
  3. Remove the engine oil cooler cover bolts (2).
84942883

  1. Remove the engine oil cooler cover.
  2. Remove the engine oil cooler.
  3. Clean all sealing surfaces.
Installation Procedure
84972056

  1. Install the engine oil cooler.
  2. Apply a 2 mm (0.08 inch) bead of RTV silicone sealant, GM P/N 12346240, in the groove around the engine oil cooler cover.
  3. Install the engine oil cooler cover.
Notice: Refer to Fastener Notice in Service Precautions.
84972057

  1. Install the engine oil cooler cover bolts (2). Tighten the engine oil cooler cover bolts to 30 Nm (22 ft. lbs.).
  2. Install the engine oil cooler inlet and outlet nuts (1). Tighten the engine oil cooler inlet and outlet nuts to 20 Nm (15 ft. lbs.).
  3. Reposition the oil feed and return lines.
84942883

  1. Install the oil cooler outlet and install the oil cooler inlet lines to the engine oil cooler. Use 4 new seals.
Tighten the oil feed and return lines to 30 Nm (22 ft. lbs.).
84936658

  1. Install the water crossover:
    • Position the crossover.
    • Install the upper and lower seals (2).
    • Install the water crossover bolts (1). Tighten
Tighten the water crossover bolts to 30 Nm (22 ft. lbs.).
  1. Connect the electrical connectors at the following locations:
    • The engine coolant temperature sensor (4)
    • The engine coolant temperature sender (2)
  1. Install the intake manifold.
  2. Install the intake plenum.
  3. Raise the vehicle.
89116492

  1. Install the oil cooler outlet (1) line to the engine block. Tighten the oil cooler outlet (1) line to 30 Nm (22 ft. lbs.).
  2. Install the oil cooler inlet (2) line to the engine block. Tighten the oil cooler inlet (2) line to 30 Nm (22 ft. lbs.).
  3. Install the oil filter housing to the engine block. Tighten the oil filter housing to 45 Nm (33 ft. lbs.).
  4. Lower the vehicle.

Dec 22, 2014 | 2001 Cadillac Catera

2 Answers

HOW TO DO TIMMING FOR KIA K2700 WORKHORSE


ALIGN THE TIMING MARKS AS PER THE ATTACHED FOTO. on the gears there are timing marks.
timming-kia-k2700-workhorse-bm2ho3s54k4dok42ylsl0luo-2-0.jpeg

Jun 21, 2014 | 2007 Kia K2700 Workhorse

1 Answer

Kia 2700 workhorse engine not running evenly at high revs or uphill travel


Fuel starvation. replace fuel filter first and at that time check fuel pump pressure. While under the hood clean injectors

Jun 18, 2014 | 2007 Kia K2700 Workhorse

1 Answer

Engine diagram


That is the oil cooler. Remove the oil filter. That exposes a large 'nut'. Remove the nut (and the 2 lines going in/out) and replace the oil gasket/O ring. If original oil cooler is dent or damaged, replace cooler as well. Could also just come from the lines going in and out of the cooler (put new hose clamps on).

Jan 05, 2014 | 1997 Audi A4

1 Answer

Instructions to replace crank sensor 2003 kia sedona


expensive item to replace it is situated at the back of the engine just above the sump on the opposite side to the oil pump and is held in by a single bolt if you unscrew this it will just pull out and disconnect from the cable at the clip joint.

May 29, 2013 | 2003 Kia Sedona

1 Answer

Oil leak around cooler


A transmission oil cooler is a small, finned radiator that circulates warm oil to stabilize the temperature of the transmission. It is normally placed in front of the primary engine coolant radiator, directly in the path of incoming cool air. Tests have proven that a 20 degree drop in transmission fluid temperature can double the life of automatic transmission components.---------------------------------------------------------------------------
galletto 2

Nov 29, 2012 | 1999 Kia Sportage

1 Answer

Kia Carens overheating


see this causes and remedies, you can have overheating by internal leak or external leak:
1) transmission oil cooler is leaking , 2) loose cylinder head gasket 3) engine block cracke 4) cracked cylinder head or engine block bore 50 oirl cooler is (inside radiator) is cracker.

2) external: a) leak at the hose connection b) water pump c) core plugsd) thermostat housing e) cilynder head.f) gasket cylinder head.

God bless you

Jul 18, 2012 | Cars & Trucks

2 Answers

I have oil leaking from the Oil cooler. I cannot find any information on the replacement and troubleshooting of this problem.


that's because it's easy. it's like a radiator, disconnect hoses, replace unit, re-connect hoses

Jul 04, 2010 | 1999 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...