Question about Dodge Ram 1500

1 Answer

Stop lamp fuse stays on when shut off - Ram 1500 Dodge Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 5,252 Answers

Check the brake light switch on the brake pedal to see if it needs adjusting.

Posted on Jul 22, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2006 chevrolet silverado 1500, where is the back brake light fuse?


Stop Lamps
The STOP LP 25-amp fuse in the underhood fuse block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to both the STOP 15-amp fuse and the center high mounted stop lamp (CHMSL) 10-amp fuse in the instrument panel (I/P) fuse block, and to the turn signal/hazard module. The turn signal/hazard module then supplies voltage to both of the trailer rear turn/stop lamp supply voltage circuits. The voltage from the CHMSL 10-amp fuse is to the CHMSL and the trailer jumper harness. The voltage from the STOP 15-amp fuse is to the stop lamps, throttle actuator control (TAC) module, and the cruise control.

Apr 08, 2017 | Chevrolet Cars & Trucks

1 Answer

2000 pontiac montana - brake lights stay on - all wires disconnected from switches at pedal


Maybe a problem with electrical connector that allows org wire to short to whit wire? The org wire is hot all the time, the whit wire becomes hot and carries voltage for brake lamps when switch is activated. Maybe whit wire is shorted to voltage, somewhere else. If you pull the stop lamp fuse, does it kill the brake lamps?

26340714-uzta3onw4mz1ggueu0gczi1j-2-0.jpg

Nov 04, 2016 | 2000 Pontiac Montana

2 Answers

2007 h3 hummer right rear brake light wont go off


Are you sure that is the brake light staying on and not the tail light

Jun 21, 2016 | Hummer Cars & Trucks

1 Answer

How do i find wiring diagram for stop lights


The STOP LP 25 A fuse in the underhood fuse block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to both the STOP 15 A fuse and the CHMSL 10 A fuse in the I/P fuse block, and to the turn signal/hazard module. The turn signal/hazard module then supplies voltage to both of the trailer rear turn/stop lamp supply voltage circuits. The voltage from the CHMSL 10 A fuse is to the center high mounted stop lamp (CHMSL) and the trailer jumper harness. The voltage from the STOP 15 A fuse is to the stop lamps, throttle actuator control (TAC) module, and the cruise control.
Do you know what a stop lamp switch is ? If so I would check it with a DVOM digital volt ohm meter , after you check fuse .
Did

Nov 05, 2015 | 2005 Chevrolet Chevrolet Avalanche 1500 LS

2 Answers

Brake lights 2001 Oldsmobile aurora


switch may have failed under dash at brake pedal arm or got unplugged but BIG FEET

Sep 10, 2015 | 2001 Oldsmobile Aurora

3 Answers

Brake lights went out so I changed a blown fuse,now the brake lights wont shut off,so I replaced the brake switch at the pedal and still have the same issue,lights wont go off.


Which fuse did you replace ? The one in the under hood fuse box or one of the two in the I/P fuse box . Do the CHMSL - center high mount stop lamps work correctly ? Here is a description how they work .
Stop Lamps
The STOP LP 25 A fuse in the underhood fuse block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to both the STOP 15 A fuse and the CHMSL 10 A fuse in the I/P fuse block, and to the turn signal/hazard module. The turn signal/hazard module then supplies voltage to both of the trailer rear turn/stop lamp supply voltage circuits. The voltage from the CHMSL 10 A fuse is to the center high mounted stop lamp (CHMSL) and the trailer jumper harness. The voltage from the STOP 15 A fuse is to the stop lamps, throttle actuator control (TAC) module, and the cruise control.
Does yours have trailer light hook up ? If so check trailer wiring connector for corrosion . Also check the turn signal / hazard module .
Does

Aug 23, 2015 | 2003 Cadillac Escalade

1 Answer

94 Mercury Cougar 4.6L Int Lamps 10Amp fuse blows


replace the door jamb light button, it's probably bent therefore not pushing in when door is shut, and when door is shut it grounds out, and it wld'nt effect the dome light because it's in the circuit befor the dome if this is the case and you find it's bent or crimped try to bend it back out,

Aug 25, 2012 | 1994 Mercury Cougar

1 Answer

Trailer connection not working need to know which fuse to change 2005 Ford F150 Lariat


Trailer Tow reversing relay ( non serviceable ) and the Trailer tow parking lamp relay are both fed from Fuse #10 ( coil on reversing relay is fed from reverse lamps & coil on parking lamp relay is fed from the parking lamps ).

Trailer Tow battery charge relay is fed from Fuse #106 ( coil is fed by fuse #13, hot in start / run position from key ).

Right Stop / Turn is fed from Fuse #36 ( powered from MFS circuit for truck stop/turn )
Left Stop / Turn is fed from Fuse #42 ( powered from MFS circuit for truck stop/turn )

Parking lamp is

Oct 17, 2009 | 2005 Ford F-150

3 Answers

Park lamps stay on


Hi! Check the switch, it could be malfunctioning.

Dec 30, 2008 | 2007 Hyundai Sonata Limited Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...