Question about 2003 Nissan Altima

1 Answer

Ipdm My a/c quit and the mechanic decided it was a bad IPDM. Since replacing this, the fan direction "mode" button has stopped working, the temp sensor has intermittent problems and I have ice cold defroster function unless I crank to 90 degrees. What have these guys done to my car?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 352 Answers

REPLACED THE WRONG COMPONENT...OR NOT FOUND THE COMPLETE ISSUE

Posted on Jul 21, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 454 Answers

SOURCE: IPDM on backorder

Don't wait for the overpriced dealer part.

http://www.titantalk.com/forums/titan-faq-howto-area/106172-ecu-relay-source-titanblue-7-solution.html

Posted on May 22, 2010

  • 183 Answers

SOURCE: AC compressor won't engage. When hooked directly

Low pressure

Posted on Jul 27, 2010

jeffsterrett
  • 98 Answers

SOURCE: WHAT DOES IPDM CONTROL ON 2004 NISSAN MAXIMA?

IPDM is Intelligent Power Distribution Module. Basically think of it as a 'Smart' Fuse Box.

Posted on Oct 23, 2011

emissionwiz
  • 75066 Answers

SOURCE: locate relay nissan quest a/c compressor relay

I am sorry we have no wiring diagrams. You can access them here for a small fee.

Posted on Oct 02, 2012

  • 550 Answers

SOURCE: my 2008 magnum was not turning on,Went to the dealer they send it was the IPDM relay . Run fine for 3 days .Now doing the samething ..

Hi,
There is an IPDM 'board' the relay plugs into. The relay is only a temporary fix. Contact the dealer (do you have a dodge or Nissan???) about the board and look on line for how to swap it out.
GL,
TD

Posted on Oct 10, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the passenger side low beam fuse located on a 2006 Nissan Altima


Low Beam Operation With the lighting switch in 2ND position, the BCM receives input requesting the headlamps to illuminate. This input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the IPDM E/R controls the headlamp low relay coil. When energized, this relay directs power ? through 15A fuse (No. 36, located in the IPDM E/R) ? through IPDM E/R terminal 20 ? to headlamp RH terminal 1, and ? through 15A fuse (No. 45, located in the IPDM E/R) ? through IPDM E/R terminal 30 ? to headlamp LH terminal 1. Ground is supplied ? to headlamp RH terminal 2 ? to headlamp LH terminal 2 ? through grounds E15 and E24. With power and ground supplied, low beam headlamps illuminate.

IPDM E/R - fuse box E/R -- engine room , under hood fuse box .

System Description EKS008LH Control of the headlamp system operation is dependent upon the position of the combination switch (lighting switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input requesting the headlamps (and tail lamps) to illuminate. This input is communicated to the IPDM E/R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (central processing unit) of the IPDM E/R controls the headlamp high and headlamp low relay coils. When energized, these relays direct power to the respective headlamps, which then illuminate. OUTLINE Power is supplied at all times ? to headlamp high relay, located in the IPDM E/R, and ? to headlamp low relay, located in the IPDM E/R, and ? through 50A fusible link (letter f , located in the fuse and fusible link box) ? to BCM terminal 70. With the ignition switch in the ON or START position, power is supplied ? through 10A fuse [No. 1, located in the fuse block (J/B)] ? to BCM terminal 38. With the ignition switch in the ACC or ON position, power is supplied ? through 10A fuse [No. 6, located in the fuse block (J/B)] ? to BCM terminal 11. Ground is supplied

https://carmanuals2.com/brand/nissan/altima-2006-4924

May 05, 2017 | Nissan Cars & Trucks

1 Answer

Replaced engine fuse box (with ipdm )on 2003 Nissan Altima SL and now the wipers will not turn off even with switch removed


With IPDM - intelligent power distribution module . Pull the front wiper relay and front wiper hi relay , see if they reset . If that doesn't work you'll need to take it to the dealer an have them reset with factory scan tool . Also ,sometimes new modules need to be programmed . Download 2003 Nissan Altima Wiper Washer Section WW PDF Manual 36 Pages

Feb 14, 2017 | Nissan Cars & Trucks

1 Answer

The a/c comes on and off even when it is in off mode.Should I change the ipdm panel?


Have the codes read, takes a scanner. I could be the IPDM, could be the A/C control module.

Jul 09, 2016 | 2004 Nissan Quest

1 Answer

Brake lights work. Why don't tail lights and tag light?


Does the front park lights work and does the vehicle have Daytime Running Lights? If it doesn't have DRL make sure fuse 53 (10A) is good and has power. The stop lamps and tail lamps use the same B61 ground. The ground should be ok. If the fuse is good and has power then there is a possibility there is an open in the circuit between the fuse and the E117 connector or a disconnect at the connector. If it does have DRL it is possible the DRL relay does not have power (fuse 59 in the IPDM 10A) or it is faulty or the IPDM is not grounding it.

Jan 30, 2016 | Nissan 370Z (2010)

1 Answer

Where is exact location of low beam driver side fuse 2007 Sentra ?


HEADLAMP (FOR USA)
LT-21
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: December 2006
2007 Sentra
8.
CHECK HEADLAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector (A) and
headlamp harness connector (B).
OK or NG
OK >> Replace IPDM E/R. Refer to
PG-30, "
Removal and
Installation of IPDM E/R
"
.
NG >> Repair harness or connector.
Headlamp Low Beam Does Not Illuminate (One Side)
EKS00JMQ
1.
HEADLAMP LOW BEAM FUSE INSPECTION
Inspect 15A fuse [No. 40 (LH) and No. 41 (RH) located in IPDM E/R].
OK or NG
OK >> GO TO 2.
NG >> Repair harness

Jan 27, 2016 | Cars & Trucks

1 Answer

My 2008 magnum was not turning on,Went to the dealer they send it was the IPDM relay . Run fine for 3 days .Now doing the samething ..


Hi,
There is an IPDM 'board' the relay plugs into. The relay is only a temporary fix. Contact the dealer (do you have a dodge or Nissan???) about the board and look on line for how to swap it out.
GL,
TD

Oct 10, 2012 | 2008 Nissan Rogue

2 Answers

I have the same problem as discribed below. 2007 Nissan Frontier -- Trailer running lights stopped working. Brake lights and turn signals still work. Where is the fuse for the trailers running lights....


the fuse is inside of the IPDM the white box on r/h side of truck by the battery. there is a black cover that you have to remove to see the white IPDM box. the IPDM has fuses and relays. the tail lamp fuse is the 10amp fuse las one in the row of fuses. its by it self with no fuses next to it. check the IPDM cover on the inside. its marked.

Sep 16, 2011 | 2007 Nissan Frontier SE Crew Cab

1 Answer

THE AUTO DOOR LOCK AND POWER WINDOW DO NOT WORK AND I CANT FIND THE FUSE FOR THEM ON 2005 NISSAN ALTIMA


From the service manual, which is available relatively inexpensive at Promanuals.net here

 Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room)
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM (body control module)
 BCM controls front wiper LO, HI, and INT (intermittent) operation
 IPDM E/R operates the wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
 through 50A fusible link (letter f , located in the fuse and fusible link box)
 to BCM terminal 70, and
 through 20A fuse (No. 39, located in the IPDM E/R)
 to front wiper relay, located in the IPDM E/R
With the ignition switch in ON or START position, power is supplied at all times
 through 10A fuse [No. 1, located in the fuse block (J/B)]

Sep 28, 2009 | 2005 Nissan Altima

1 Answer

Was running fine then stalled suddenly. when it started back run rough at an idle black smoke from exhaust then press the gas pedal and it quit now it will not start at all


I just had a similar situation. The truck would run fine and then the Service Engine Soon light would start blinking and the truck would go into "limp" mode. It would eventually stall. Strangley though, if I turned the key over and then restarted it, it would start right up and run again. It ended up being the IPDM (Intelligent Power Distribution Module) that was bad. It cost me $520 to replace it.

Sep 28, 2009 | 2005 Nissan Frontier

Not finding what you are looking for?
2003 Nissan Altima Logo

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...