Question about Suzuki Cars & Trucks

1 Answer

How to renew coolant on a suzuki splash

I have drained off the old coolant where do you refill it /

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

Double post?
and again no year, or engine option. (size)

Posted on Sep 15, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 713 Answers

SOURCE: How to flush coolant from 04 suzuki verona, I saw

easiest way is to open drain plug on the radiator let it drain in bucket till it stops refill with water until you get all the coolant out. next time you refill put a cleaner in it and run it down the road at normal operating temperature for about 30 minutes let it cool off and flush it a couple more times with just water when it is clear add antifreeze in a 50/50 mixture one bottle antifreeze one bottle of water.

Posted on Aug 30, 2009

  • 299 Answers

SOURCE: How to drain and refill coolant in a 2004 Jeep 3.7L Liberty?

you drain it from the radiator petcock on the bottom and you fill it from the overflow tank however I seem to remember those cars as having a radiator cap if i'm not mistaken it is on the passenger side if not in is the overflow tank

Posted on Sep 23, 2009

  • 5370 Answers

SOURCE: drain and refill coolant on my 2000 chevy 2500 6.0 liter pickup,not sure on correct procedure on refilling coolant.

For how to change coolant on chevy pickup,click the link below and follow the detailed procedure:---
http://answerguide.blogspot.com/2012/01/how-to-change-coolant-on-chevy-2500.html
---------Thanks.

Posted on Jan 26, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE does the antifreeze go in Suzuki eiger 400 4x4 05 go? I don't see an radiator cap or anything


there will be an expansion tank that hold/refill the coolant , look for plastic tank could be round , square beside rad , with coolant hoses to it , make sure engine cold when removing cap, will need to drain old coolant before refilling with new , worth checking the coolant strenght before draining as may still be ok

Jun 08, 2017 | Suzuki Cars & Trucks

1 Answer

How to change radiator drain plug


Simply loosen the old one in the radiator to let the coolant run out. After the radiator is empty, pull the old drain cock out of the radiator and install the new one. Tighten the new one up firmly and refill with coolant. Let the engine run to reach normal operating temperature and check for leaks.

Jul 09, 2014 | 1991 GMC Sonoma

1 Answer

Radiator cap


old post.
yes the RAD cap
car has 3 diff, engines. so. can;t be specific.
what year 2008+?
ok, allcars,
you fill it to get the block full and the Radiator to the top
the side tank , only major function is for the cool down.
during cool down it allows the RAD to **** back coolant, as she cools.
it also prevents green AF on the pavement as engine gets hot.
that second part is for pollution rules.

the car has a FSM, manual, in there are rules for your car and you opted engine.
The plumbing on all cars , all engines, very by same.
FWD, RWD, too.
as does some other options. (block eaters?)

if you read service books
it tells you, to burp the engine and rad.
I run the engine for 2 heat cycles, and then when cool
i check that the rad fluid is full to the top of the RAD.
Here is what id do , (assumes thermostat not pulled)
I fill the rad with 50% AF.
i run motor util it starts to expand, if the level drops as i run motor
I add more, then when the AF starts to leak out, I cap it off.
then fill the side tank (expanson tank) 1/2
i watch the tank for 2 days. to get out all air. in the system.
if my dash coolant gauge, shows odd readings, at any time.
say it is not constant rise to 200f , I know I have air in the system.
If true, i use burping techniques,, ASK !
All mech's know about this....
also putting a thermostat in wrong will trap air.
the stat as a bleed hole that MUST be up hill side.
or will trap air.

now I answered for you and 1billion other water cooled engine owners.

Jul 21, 2013 | Suzuki Cars & Trucks

1 Answer

Install a radiator


R&R? remove and return.?
(drain coolant)
remove all rad hoses.
remove all bolts holding in rad.
remove rad.
reverse and refill with 50% AF.
same steps as all cars 100 years.
drain and replace, refill.

Mar 09, 2013 | 2005 Suzuki Forenza

1 Answer

Where is draintap on block of kia serento 2.5 tdi


Just open radiator drain & coolant cap

Drain & refill ----every 3years

If your a perfectionist drive a day or two
& do again,then all the old will be gone

Dec 01, 2012 | 2005 Kia Sorento 2.5

1 Answer

A complet raditor system and wash tank


put fuel injection cleaner in gas tank, put flush in your coolant system drain completely then refill with manufacture recommended coolant.

Mar 21, 2011 | 2007 Suzuki Grand Vitara 4WD

1 Answer

2004 LeSabre Limited - Have a noise that sounds like water sloshing under the dash when making turns or sudden stops. Mechanic checked the A/C drain and claims it is clear. Any ideas?


Its the heater core. There is air in it allowing the coolant to splash inside it. You should bleed the cooling system. Its good to flush it out completely and refill it correctly.

Oct 15, 2010 | 2004 Buick LeSabre

1 Answer

How do i take off the old water pump on 1996 geo metro 4 cyl?


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the air cleaner.
  4. Remove the suction pipe bracket for the A/C compressor, if equipped.
  5. Loosen but do not remove the 4 water pump pulley bolts.
  6. Raise and safely support the vehicle.
  7. Remove the lower splash shield.
  8. Remove the A/C compressor drive belt, if equipped.
  9. Remove the alternator drive belt.
  10. Remove the crankshaft and water pump pulleys.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts and remove the water pump from the engine.


ae1b66e.gif
Water pump mounting location

  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten the bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten the bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and tube.
  7. Install the timing belt.
  8. Install the water pump and crankshaft pulleys. Leave the water pump pulley bolts hand-tight.
  9. Install the alternator drive belt.
  10. Install the lower alternator cover plate and tighten the bolts to 89 inch lbs. (10 Nm).
  11. Install the A/C compressor drive belt, if equipped.
  12. Install the lower splash shield and lower the vehicle.
  13. Tighten the water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  14. Adjust the water pump drive belt tension and tighten the alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  15. Install the suction pipe bracket for the A/C compressor, if equipped.
  16. Install the air cleaner.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and check for leaks.


83667f6.gif Water pump assembly showing rubber seal location


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.

    CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

  3. Remove the air cleaner assembly.
  4. Loosen but do not remove the four coolant pump pulley bolts.
  5. Raise and support the vehicle safely.
  6. Remove the lower splash shield.
  7. Remove the air conditioner compressor drive belt.
  8. Remove the lower alternator cover plate bolts, loosen the alternator adjusting bolt, and remove the drive belt.
  9. Remove the crankshaft pulley.
  10. Remove the coolant pump pulley.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and guide tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts. Remove the water pump from the vehicle.
To install:
  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and guide tube.
  7. Install the timing belt.
  8. Install the water pump pulley and leave the bolts hand tight.
  9. Install the crankshaft pulley.
  10. Install the water pump/alternator drive belt.
  11. Install the lower alternator cover plate and tighten bolts to 89 inch lbs. (10 Nm).
  12. Install the air conditioner compressor drive belt by releasing the tensioner pulley and installing belt.
  13. Install the lower splash shield and lower vehicle.
  14. Tighten water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  15. Adjust the water pump drive belt tension and tighten alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  16. Install the air cleaner assembly.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and allow it to reach operating temperature. Check for leaks and refill cooling system as necessary.

Mar 06, 2010 | 1996 Geo Metro

2 Answers

How do i change coolant ,I drained system from resivoir cause there is no rad cap but trying to refill with coolant is impossible the system wont take fluid out of resivor now and light gage inside says...


see if you can remove top radiator hose at highest oint on motor  and fill, you can drain coolant at bottom of radiator with wing nut type drain fitting

Sep 27, 2009 | 1997 Pontiac Sunfire

1 Answer

How to flush coolant from 04 suzuki verona, I saw


easiest way is to open drain plug on the radiator let it drain in bucket till it stops refill with water until you get all the coolant out. next time you refill put a cleaner in it and run it down the road at normal operating temperature for about 30 minutes let it cool off and flush it a couple more times with just water when it is clear add antifreeze in a 50/50 mixture one bottle antifreeze one bottle of water.

Aug 30, 2009 | 2004 Suzuki Verona

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...