Question about 2003 Cadillac Deville

Open Question

How much should it cost to have the pressure power steering hose replaced at a shop

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: Power Steering Pressure hose, 1976 Cadillac Eldorado

yes you can repair it and you are right about the flang try this website to see if they have your car listed www.autozone.com to get pictures and diagram i also would like to give you this information website www.schramauto.com if you ever have any hard to find GM-parts Schram auto & truck parts sells only GM-parts and i hope i have been some help to you and you have a nice car.

Posted on Apr 25, 2009

mc1bean
  • 3053 Answers

SOURCE: Had a power steering leak, changed pump still had

Hello,

Power steering systems are actually pretty basic as far as operation, however pain in the **** when it comes to leaks. As read, you said you had leak in what you thought was in your power steering pump, and then found out it was the hi pressure hose that was leaking, Unless your car has some type of fuse that controls it in your fuse panel. (check owners manual, to see if you have a relay type of fuse that controls the electrical circuit that triggers the pump) if so, it could of got blown. However, I believe this is what has happened. When you had a leak in the power steering, you thought it was the pump, so you replaced the pump, which of course pump was probably bad because of lack of fluid circulation with a leak, it instantly will dry out, from high heat of friction from barrings, metal on metal with no fluid. Now, that being said, you put new pump on, but sense the leak was actually off the high pressure hose, means it is highly possible that your new pump, by driving it for even 10 minutes, with the leak of high pressure hose, could of cause new pump to burnout. So, at worse case example, you have burnt up new pump, because of the time you replace the high pressure hose might of already done the damage to the new pump. But, before you go that route of replacing again, the new pump, check all your wire connections that are triggering the pump. Make sure all connections are hooked up good, and making good contact, as even the pump has to have power supply to trigger it, and check to see if inline fuse (if has one) is good and of course as said earlier fuse box to see if as a safety feature, sense would be low on fluid with a leak if it blew the fuse that controls the electronics that go to the pump , make sure it is good. I hope this helps you in the areas to look. Places like AUTO ZONE, can look up your car and let you know for sure if your pump is controlled by a separate fuse and where it would be. Thanks Mike from Fixya

Posted on Aug 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where I can get 1993 infinity j30 power steering pressure hose or it compatible part at low cost?


low cost will be from a wrecker that handles your make of car
hydraulic hose shops can manufacture one if you provide the sample
that will be about 1/2 cost of a genuine hose
genuine as a last resort

Oct 03, 2015 | Cars & Trucks

1 Answer

Power steering pressure hose replacement


I need more info to help you. Take it to a good shop. It is ok to drive it there, just try to tape or plug or wrap the hose just in case all the fluid has not drained out you don't want to make a mess. It will be hard to steer, you will just have to drive old school, like it was before power steering. Mike

Oct 07, 2014 | 2006 Kia Sorento 3.5

1 Answer

How do i install power steering hose on a 1991 lexus 400


If you notice problem with power steering,the hose has to be inspected,if its faulty it has to be replaced.

=========
For your help,i provide you with few solved helplinks showing how exactly to replace power steering hose:------

How to Remove Power steering Pressure Hose ?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

---------

How to replace power steering pressure hose?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

--------------
These will help.
Thanks.

Nov 28, 2012 | 1991 Lexus LS 400

1 Answer

Volvo s40 power steering pressure line change job cost


The cost can cary depending on the labor rate at the shop you take it to. I can tell you this though, the book time in the labor guide for changing the line says it is 1.1 hours of labor and list cost for the hose is $155.70. Of course there will be a shop supply charge (depends on which shop and thier going rate) as well as the cost for the power steering fluid. I hope I was able to help

Mar 08, 2012 | 2002 Volvo S40

1 Answer

How Long to replace a power steering pressure hose? Labor cost?


6 cylinder engine remove and replace pressure power steering hose.

2.2 hrs X there shop labor rate = your labor cost.

Pre Mitchell labor guide

Jun 11, 2010 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Is the Steering Pump Pressure Hose


the only wany you will know is if the hose looks new well newer than the other one

Nov 28, 2009 | 2003 Ford ZX2

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

2 Answers

My power steering pressure hose has a leak.


i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE
  1. Remove the power steering pressure hose (2) from the power steering pump (1).
  2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
  3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
  4. Remove the power steering pressure hose (1) from the power steering gear (3).
  5. Remove the power steering hose retainer (2).
  6. Remove the power steering pressure hose (1) from the vehicle
    1. Install the power steering pressure hose (1) to the vehicle
    2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
    3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
    4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
    5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Mar 27, 2009 | 1999 Pontiac Sunfire

2 Answers

I need to rplace tke power steering hose on a 2000 kia sephia


we tried fixing the old power steering hose, finally just had it taken off and another made up by an auto shop, cost $65 to have one made. very easy to fix, just undo at each end. this is a pressure hose though so make sure and get the same kind made.

Nov 08, 2008 | 2000 Kia Sephia

Not finding what you are looking for?
2003 Cadillac Deville Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...