Question about 2010 Rolls Royce Ghost

Open Question

Instrument cluster remove

Is just out of warranty and a bulb in the cluster has gone, how do i remove the cluster

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dash light behind outside temp has gone out, how do you replace it?


pull out the instrument cluster by using the dash removal hooks. can be bought from mercedes dealer on any tool dealer like snapon or mac. all u do is to insert the hooks on either side of the instrument cluster usually on yhe lower sides and u will feel the hooks grab th instrument cluster. carefully pull the cluster out and disconnect the plug. you might have to have the steering wheel in the extended position to slide out the clucter. once you have the cluster out replace the bulb directly behind.

Sep 01, 2010 | 2000 Mercedes-Benz CLK

1 Answer

Instrument cluster lights don't work. Fuses and bulbs are good.


feed wire for the lights may have failed or the circuit on the board may have gone. if you remove the cluster you can put a supply to the bulb circuit (carefully) and check if it is the circuit. If it's ok you can run a new feed to the cluster from your lights. Job done.

Feb 16, 2010 | 1995 Jeep Cherokee

1 Answer

How do you change the instrument light bulbs?


you have to take out the instrument cluster and then twist the hold down a half turn and pull to remove bulb and hold down from cluster then remove bulb from hold down replace with working bulb and reverse to install working bulb then reinstall instrument cluster.

Feb 13, 2010 | 2003 Kia Sedona

1 Answer

Need to replace instrument cluster/AC bulbs


Hello, You can obtain a 2004 Ram Factory Service Manual with all of that information available from Promanuals.net. The reason why it may be so important is because right before the removal instructions the service manual has diagnostic instructions to try. There are numerous pages on removing the instrument cluster, and cluster bezel.

(1) Disconnect and isolate the battery negative
cable. (For Airbag)

(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - REMOVAL).

(3) Remove the four screws that secure the instrument
cluster to the instrument panel structural support
(Fig. 5).

(4) Pull the instrument cluster rearward far
enough to access and disconnect the instrument
panel wire harness connectors for the cluster from
the connector receptacles on the back of the cluster
housing.

(5) Remove the instrument cluster from the instrument
panel.
9e8a042.jpg

Oct 01, 2009 | 2004 Dodge Ram 1500

1 Answer

Warning lights is on the red triangle volvo s40 2005 2litter


Sounds like the instrument cluster has gone bad or a bulb in the cluster has burnt out. You will need to remove the cluster and check the bulbs to see if they need to be replaced.


Aug 07, 2009 | 2005 Volvo S40

1 Answer

Instrument cluster removal 1965 mustang


  1. Disconnect the battery cable.
  2. Disconnect the speedometer cable from the speedometer head.
  3. Remove the six screws retaining the instrument cluster assembly to the instrument panel and tilt the cluster forward.
  4. Disconnect the wiring and the bulb sockets and remove the cluster assembly. NOTE: All individual instruments may be removed and serviced at this time. To install:
  5. Position the cluster and connect the wiring and bulb sockets.
  6. Install the instrument cluster assembly to the instrument panel with the six retaining screws.
  7. Connect the speedometer cable and the battery cable.
  8. Check the operation of all gauges, lights, and signals.

Jun 25, 2009 | 1965 Ford Mustang

2 Answers

Check engine light does not turn on at all


The bulb is probably loose and/or burnt out. If you are mechanically inclined you can tackle this job... This procedure is the one i use, most often it's the blue high beam indicator bulb that goes so if you want to change it while your in there.....(hint hint)
Disconnect and isolate the battery negative cable. Wait a good 2 minutes to allow for air bag deactivation...NOTE: USE CAUTION ...Lower the tilt wheel to lowest position.
Remove the cluster bezel from the instrument panel.
Remove the two screws that secure the upper mounting tabs of the instrument cluster to the underside of the instrument cluster hood formation of the instrument panel top pad.
Remove the two screws that secure the lower mounting tabs of the instrument cluster to the instrument panel structural duct.
Pull the upper mounting tabs of the instrument cluster downward, then pull the instrument cluster rearward far enough to access the instrument panel wire harness connector for the instrument cluster. Disconnect the instrument panel wire harness connector for the instrument cluster from the connector receptacle on the back of the instrument cluster housing.
Remove the instrument cluster from the instrument panel. Now do you remember which bulb it was? You can now see where the check engine light bulb is mounted. Twist and remove, install in reverse order. In some cases they are just loose or not making good ground, but after going through this just to access that lil bugger, i'd replace it.
I hope i have helped you and if you feel i have please acknowledge.
Be well and keep the cherokees alive....

May 13, 2009 | 2001 Jeep Cherokee

1 Answer

I need to change the bulb in the analog clock in my 1999 Lincoln Towncar. How do I go about getting to it without tearing apart the dashboard?


you need a special tool to get the radio out. It has pins that spread out spring clips so the radio can pull out.

please rate as solved if this helps.

SECTION 413-00: Instrument Cluster and Panel Lighting — General Information 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Bulb —Electric Clock
Special Tool(s) Radio Removing Tool
T87P-19061-A

2242b54.gif
Removal
  1. Disconnect the battery ground cable.
  1. Pull out the radio using Radio Removing Tool.
1475891.gif
  1. Remove the radio.
    1. Disconnect the electrical connectors.
    1. Disconnect the antenna cable.
    1. Remove the radio.
  1. Remove the instrument cluster finish panel bolts.
c7eab47.gif
  1. Remove the instrument cluster finish panel bolts.
054ed10.gif
  1. Pull out and position aside the instrument cluster finish panel.
cc71028.gif
  1. Disconnect the electric clock electrical connector.
  1. Remove the instrument cluster finish panel.
    1. Disconnect the headlight switch electrical connector.
    1. Disconnect the dimmer switch electrical connector.
    1. Remove the instrument cluster finish panel.
  1. Remove the electric clock illumination bulb.

Apr 23, 2009 | 1999 Lincoln Town Car

1 Answer

Changing instrument panel light bulbs


You have to remove the entire cluster assembly to get to the bulbs, there is no other way, no room for this man's hand at the back.

Nov 09, 2008 | 2005 Dodge Caravan

Not finding what you are looking for?
2010 Rolls Royce Ghost Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rolls Royce Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Are you a Rolls Royce Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...