Question about Cars & Trucks

Open Question

My hyundai i10 wont lock or unlock when using the press button on the key

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bad_dog1
  • 104 Answers

SOURCE: drivers door power lock wont work.

Either the wring going to that motor or the motor itself is bad.

Posted on Mar 09, 2009

Ad
Murphybanton
  • 2004 Answers

SOURCE: key fob for hyundai elantra not working

Please dont worry yourself so much the security locks needs to be reprogrammed to enable it work effectively. Same happens to other vehicles as well.

Consult Hyundai garage close to you or if you have it in your manual.

Good luck.

rate this.

Posted on Apr 14, 2009

ghost4548
  • 776 Answers

SOURCE: Hyundai 2002 sonata,,,, car has power locks.

You are correct in your assumption about a relay... there are two relays. One is for 'LOCKING' the other is for 'UN-LOCKING.' They are both labeled as "LOCK" relays (1 & 2). You can verify if a relay is bad by swapping one with the other. If the problem moves to 'unlocking' the doors, but will NOW LOCK - the relay is bad. If not, further troubleshooting is necessary.
5ea2f1e.jpg e879d13.jpg efcc6be.jpg

Posted on Jun 07, 2009

  • 1071 Answers

SOURCE: 97 Golf,lock/unlock button inoperative and must

drivers door latch is bad there is a module in the latch so the electric side is inop

Posted on Jul 30, 2009

SOURCE: WHAT DIAGNOSTIC PROTOCOL IS USED ON i10 1.1ES

dear friend-your i10 has a obd2 plug and it is situated next to bonnet lever below the fuse box,a normal
GLOBAL DIAGNOSTIC SYSTEM monitor will be good to solve your problem.

Posted on Nov 05, 2009

Testimonial: "well hidden! but exactly where you said. Thanks."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In my Hyundai I10 there is fault with central locking, when open it unlocks and immediately locks back, it does not stay opened


the length of time that a car says unlocked is dependent on the make
most are around 30 seconds before it relocks itself
to stop it relocking just open a door and then close it and it stays unlocke d

Dec 17, 2016 | Hyundai Cars & Trucks

1 Answer

Why is my Hyundai i10 is beeping when the door opens?


If the car uses a key fob its beeping because the key is still inside the vehicle.

Jul 18, 2014 | 2010 Hyundai i10 1.1

1 Answer

Door Lock does not work


I want to know what's the fuse number for my window wipers on my 2005 ford explorer

Jan 22, 2014 | Hyundai Accent Cars & Trucks

1 Answer

Hyundai i10 Steering not rotating. It seems to be locked. Pls help. The wheels were tilted to other end so, I tried to straighten by turning the steering even before starting the engine. But when I start...


Faulty Steering?
It was not until later in the day as I check the Internet for "hyundai i10" "steering locking" that I started to worry once again. I found reviews and comments mentioning that the i10 had problems with its power steering system which sometimes caused locking while the car was in motion! This post about hyundai i10 steering locking is what really caused me to get worried again. I still puzzled a bit and not sure if that was the same case as mine as in my case the locking took place while the car was at a stand still and turned off. I'll try to follow up on this carefully to see where it goes. Perhaps I should mention this issue to the agency as they service my car after the first 1000 miles (or first month of driving it).
Update: After describing the problem on an Arabic cars forum I learned that nothing was wrong with my i10. The steering locking was normal since I tried to move the steering too much while the car was turned off. As for the key not turning in with ease, the reason was that I must have moved the steering slightly after inserting the key and before turning the key. This is the method used for turning the key whenever the steering has locked. Man, I just love those forums and i LOVE the Internet.

Oct 24, 2012 | 2010 Hyundai i10 1.2

1 Answer

I have a 2003 Hyundai Tiburon GT, the key fob doesn't work. I got battery checked, they're fine. Any ideas how to make the key fob work? It has an unlock and a lock button.


Place key in ignition, turn but do not crank up the motor and press the lock/unlock buttons to program it for your vehicle. You should see the lights flash on/off confirming a successful link.

Feb 14, 2011 | 2003 Hyundai Tiburon

2 Answers

Hyundai santa fe key fob 1 works 1 does not have changed battery deal says to buy new ,can i unlock with key without alarm going off


System operation
Pressing remote control lock button locks vehicle and activates system Fig. 1 . Indicators flash once. Pressing remote control unlock button unlocks vehicle and deactivates system Fig. 1 . Indicators flash twice.
Fig. 1
Synchronization
When
System malfunction. Remote control added or replaced.
How
Access alarm system control module located under driver's side lower fascia Fig. 2 . Set memory switch to SET position. Press remote control lock or unlock button. Set memory switch to OFF position. Confirm synchronization has been successful by locking and unlocking vehicle. Repeat procedure for second remote control. Synchronization can also be carried out using diagnostic equipment.
NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

Jul 30, 2010 | 2003 Hyundai Santa Fe

2 Answers

I need to reset my car alarm on my 02 vw golf. the battery has been replaced so alarm wont unlock doors


stick key in driver door lock and unlock it. If that works, now see if the remote will unlock the door or doors..i remember reading in an owners manual once where you can program which doors open and close by they way you press and hold down the two main buttons, also after a battery change in the remote, i think, but not sure, i did this on a blazar i once owned... the owners manual said, that you had to be within 20 feet and press and hold down both buttons till it makes the arming sound.... Can i get some feedback cause im curious..thanks.

Apr 04, 2010 | 2002 Volkswagen Golf

5 Answers

How do you reprogram a key fob for a hyundai coupe?


This came directly from my Hyundia service guy:

Unlock the car, get in and close all doors. Turn the ignition key to ACC, press the Unlock button till blinkers flash. That's it. Get out of the car and see if it works.

Good luck.

Mar 20, 2010 | 2003 Hyundai Tiburon

2 Answers

My alarm wont turn off. my car wont start. its a 2004 tiburon.


With alarm activated your ignition is disabled.Find the combination to disable it.With GM's you hold opposing buttons on the fob till it beeps twice. The dealer should help for no charge.

Feb 28, 2010 | 2004 Hyundai Tiburon

1 Answer

I replaced battery in my audi 80 2.0 tdi but have lost the remote and alarm wont stop going off .


Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction: Alarm LED in rear fog lamp switch illuminates for 30 seconds when vehicle is locked.
How
NOTE: A maximum of 4 keys can be programmed (one at a time).
As memory positions of existing keys are unlikely to be known: Obtain and reprogram all keys.
NOTE: Existing key memory positions will be overwritten.
Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Using first key, press unlock button once (programs memory position 1). Alarm horn sounds once to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF. To program remaining keys into memory positions 2, 3 and 4. Carry out the complete procedure below for each key: Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Press unlock button at 1 second intervals, as follows: Twice for memory position 2 (second key). Three times for memory position 3 (third key). Four times for memory position 4 (fourth key). Alarm horn sounds once every time unlock button is pressed, to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF.
NOTE: Ignition MUST be switched OFF between each key programming procedure

Jan 10, 2010 | 1992 Audi 80

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...