Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: jeep codes location of unit
Got me a complete manual for 199 jeep factory model and found location of each individual unit in question. Manual gives u possible solution to each code and repair and or replace. As a mechanic myself testing, trouble shooting and repair was not that difficult. Shift solenoid was very difficult to get to. Located under the head lamp passenger side.
Posted on Nov 19, 2008
Both fault codes refer at Tnasmission problem...
P0743 - Torque Converter Circuit Electrical
This DTC appears when an open or shorted condition is detected in the TCC (Torque Converter Clutch) solenoid control circuit; check this as possible causes:
- fused ignition switch output circuit open
- torque converter clutch solenoid defective
- TCC solenoid circuit w/h intermittent defect
- TCCsolenoid circuit w/h observable defect
- TCC solenoid control circuit open
- TCC solenoid control circuit short to ground
- PCM defective (TCC solenoid control circuit)
You will need remove the cover/pan to inspect the harness that goes to all the solonoids and then to inspect the valvebody and the TCC solonoid itself. If you have a multimeter then you could ohm through the harness and even the solonoid. I have found that most of the time this code was produced because of the solonoid itself. But it could be the circuits to it also. There is abig connector an top of the trans that goes into the trans and the internal harness ispect that connector for any corrosion or damaged pins or wires.
P0753 - Shift Solenoid A Electrical Malfunction
This is a common repair that I have replaced several of the solenoid but it is not a cronic problem. It be the wire going to the solenoid shorted so make sure that is check before the transmission is tilted down and the side cover removed. 90% it is just the solenoid; the solenoid is located in the side pan of the tranmission. It would mean lowering the cradle(what the engine and transmission sit on) and lowering the transmission down about one to two feet. Check this like a possible cause:
- 1-2 shift solenoid control circuit is open or shorted to ground
- 1-2 shift solenoid control circuit is shorted to voltage
- 1-2 shift solenoid has failed
- PCM has failed
You will need to remove the transmission pan and its the solenoid with the red and light green wires going to it. Let us know if you have questions contact us here.
Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using FixYa.
Posted on Oct 20, 2011
p0743-? p0138-oxygen sensor input voltage maintained above the normal operating range. p1763- governor pressure sensor volts too hi.
Posted on Dec 02, 2011
This is a wiring problem you have a loose connector at the ECT control module or connector at the transmission,the solution is make proper connection and this is a common problem,that or you have a bad conductor plate in the transmission. Go to the right rear of the engine compartment ensure you connection for the transmission module is all hook up, go to the transmission and ensure nothing at the harness is disconnected
Posted on Mar 29, 2012
Tips for a great answer:
Apr 07, 2017 | 1998 Dodge Dakota
Dec 10, 2012 | 1999 Jeep Grand Cherokee
Jul 03, 2012 | 1997 Dodge Ram 1500 Club Cab
Mar 29, 2012 | Cars & Trucks
Nov 05, 2011 | 1998 Dodge Dakota
Feb 01, 2011 | 1998 Dodge Caravan
Oct 17, 2017 | Cars & Trucks
63 people viewed this question
Usually answered in minutes!