Question about Cars & Trucks

Open Question

Toyota cressida 21r

After i change new headgasket,my cressida 21r wont start,already check all fuse,distributor,contact point,ignition coil,new spark plug but when i crank the engine,no spark to the spark plug

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Mk1 Cortina engine starting problems

Change the oil. Thick oil winter can cause it, or over diluted oil too. Got similar issue with my mark 1. Bought it but never ran more than 30 secs. Just drained 8 litres of oil out!!! Glad I changed the carby now. Hope you changed the condenser too. Once the plugs are fouled (may look OK) they are no good so might have to change them again.

Posted on Aug 11, 2008

SOURCE: i have a 1992 toyota

check your timing belt

Posted on Nov 02, 2008

frcs68
  • 1605 Answers

SOURCE: Distributor wont spark

check the fuseble link.
you can measure it, and make sure the contact are clean and secured.
the other thing is the check the ignition switch, make sure you have 12v going to the switch.
check thermo switch on top of the block.

Posted on May 21, 2009

  • 462 Answers

SOURCE: I have a 94 Toyota Corolla 1.8. Engine wont start.

Check HALL sensor , it's probably inside the distributor , another name for it is a camshaft position sensor.

Posted on Jul 15, 2010

jturcotte
  • 7699 Answers

SOURCE: my honda oddessey 1995, my

Hi, since you've replaced everything else, about the only thing left is the crankshaft position sensor. This is the sensor the computer uses to time the spark signals. Because this sensor is expensive, I recommend you test it first to verify it's bad before replacing. I have pasted test procedures below as well as replacement procedure in case it fails the tests. You will need an ohmmeter for the test. If you don't have an ohmmeter, you can buy one for as little as $10, or maybe you can borrow one. You will also need a timing light if you replace the sensor. Please let me know if you have questions, and thanks for using FixYa.


TESTING CRV and 1995 Odyssey Models

  1. With the ignition switch OFF , detach the electrical connector on the side of the distributor housing.
  2. Measure the resistance between the following two CKP wires:

    CRV models: The blue and white wires. The resistance should be 300-700 ohms. 1995 Odyssey models: The blue/green and blue/yellow wires. The resistance should be 700-1,300 ohms.
  3. If the resistance is not in the specified range, replace the distributor ignition housing.


REMOVAL & INSTALLATION CRV and 1995 Odyssey Models

  1. Remove the negative battery cable.
  2. Remove the distributor cap leaving the wires attached and place aside.
  3. Disconnect the electrical connectors at the side of the distributor housing.
  4. Make a matchmark reference mark between the distributor housing and the cylinder head and remove the distributor housing assembly.

To install:
  1. Transfer the components not supplied with the replacement distributor housing assembly.
  2. Install the distributor housing assembly in the reverse order of removal.

jturcotte_1430.gif

Fig. Fig. 2: The Crankshaft Position (CKP) Sensor rotor looks like a small gear in the lower distributor housing- CRV and 1995 Odyssey models



7. Check and reset the ignition timing as outlined below.

ADJUSTMENT CRV and 4-Cylinder Odyssey Models



If equipped with an automatic transaxle, place the shifter in Park or Neutral. If equipped with a manual transaxle place the shifter in Neutral. Make sure to apply the parking brake and block the drive wheels.


  1. With the heater off and in the full cold position, start the engine and hold the engine speed at 3000 rpm, until the radiator fan comes on at least one time. To check the ignition timing, the engine must be at idle speed and at normal operating temperature. Make sure all electrical consumers (defroster, radio, air conditioning, lights, etc.,) are turned OFF.
  2. Locate the blue plastic Service Check (SCS) Connector, as follows:

    Odyssey models with 4-cylinder engines: centrally located on the passenger side, under the dash. The connector has two wires; one is brown with a black tracer, and the other wire is red.

See Figures 1 and 2

jturcotte_393.jpg

Fig. Fig. 1: The inductive lead of the timing light is placed around the No. 1 spark plug wire; and the light is aimed toward the marks on the crankshaft pulley.


jturcotte_1431.gif

Fig. Fig. 2: The red ignition timing mark on the crankshaft pulley is lined up with the pointer. The two small notches on either side of the red colored notch represent the plus (+) or minus (-) 2° increments. The white notch to the far right is Top Dead Center (TDC)

  1. Connect the SCS service connector tool number 07PAZ-0010100 or equivalent to the service connector. A paper clip can be substituted for the tool by forming a "U" shaped bend in the paper clip and carefully inserting it into the back side of the SCS service connector terminals. The purpose of the tool is simply to connect the two wires together temporarily.
  2. Connect a timing light to No. 1 ignition wire and point the light toward the pointer on the timing belt cover.
  3. Check the idle speed and adjust if necessary.
  4. The red mark on the crankshaft pulley should be aligned with the pointer on the timing belt cover.
The white mark on the crank pulley is Top Dead Center (TDC).
  1. Adjust the ignition timing by loosening the distributor mounting bolts and rotating the distributor housing to adjust the timing. Set as follows:
    2.2L/2.3L Odyssey 2.2L models: 13-17° at 650-750 rpm
  2. Tighten the distributor bolts to 17 ft. lbs. (24 Nm) and recheck the timing.
  3. Remove the SCS service connector or the substituted paper clip from the SCS service plug.

Posted on Apr 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1949fordrepairhelp


Old school!

Check the points for being clean and flat. One side has a trough and the other side has a spike. Clean them so they are flat. Check the points gap with feeler gauges. Check you have power at the ignition coil. With power to the coil, when you disconnect the earth, you should get a spark at the plug. Check the plug gap about 25 thou. Check the rotor inside the distributor cap, it may be missing and you need one. The brass outer contact can be cleaned on the wall of the tyres (those were the days). Also check that the spring loaded contact in the CENTRE of the distributor cap goes up and down. Finally check that the distributor cap doesn't have any cracks. Watch the cap and leads in the dark whilst cranking and looks for sparks tracking to earth. Good luck. Let us know how you get on by making COMMENT under my name.

May 12, 2016 | Cars & Trucks

1 Answer

Car died while stooped at light


if it won't run on starting fluid then you have a no spark issue. i'd check spark out of the coil to the distributor. you could have a bad ignition control module or coil

Apr 18, 2014 | 1986 Toyota Cressida

1 Answer

Toyota cressida 21R lacking power


check the spark plugs if they need replacement

Jan 20, 2012 | 1986 Toyota Cressida

2 Answers

I have a toyota cressida gli 6 1989 ,has spark and fuel,motor swings but just wont start


Where had you checked spark first? Is the distributor turning? This can be checked by removing the distributor cap and making sure the shaft is turning as the engine cranks. Have you checked that there is spark at the plugs? The ignition coil could be weak and still produce some spark but not enough to start the engine. Be cautious of all rotating belts and pulleys around the engine while working under the hood.

May 19, 2011 | 1989 Toyota Cressida

1 Answer

94 toyota camery 4 cyl wont start Ichecked the fuel injectors there ok checked fuel pump works fine replace distributor cap and the ignitor but I dont get a spark at the sparkplugs.henrys


check all efi and ign fuses first...then check pickup coil and ignition coil in distributor w/ ohm meter...since you already replace the ignitor, then mostly likely it's the pickup coil or ignition coil...buy the whole

Aug 22, 2010 | 1994 Toyota Camry

1 Answer

My car has no spark in the polugs


try to change the High tension leads to the plug, check to see that the Ignition coil is working well.
Fix a plug individually to each terminal and crank the engine to see for a good spark. thereafter fix all plugs back to start. Also the platinum points inside the distributor must be checked and adjusted to the recommended settings.

Jun 25, 2010 | 1996 Toyota Corolla

2 Answers

My 1990 toyota cressida wont star, no spark from distrbuitor to selenoide


check your crank sensor also you got the correct key its not lost it chip out off it has it

Oct 20, 2009 | 1988 Toyota Cressida

2 Answers

Engine will not start


could be your distributor contact point. if you do not have contact point, then the electronic part that replaces your contact point. some called it the electronic ignite r.

you should concentrate on the spark. you can check the presence of 12 volts in your coil while starting.

the primary windings of the coil are the one in the clips or screws. check be sure that you have positive 12 v on one wire and pulsating negative from the other terminal. the negative pulses are coming from the contact point.

tnx 4 using fixya,

drcool


Sep 06, 2008 | 1987 Mazda 323 4-Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...