Question about 2000 Mercury Villager

1 Answer

Why don't my turning signal blink/work

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 12 Answers

YOU MAY HAVE A DEFECTIVE HAZARD/TURN SIGNAL FLASHER/RELAY,

Posted on Jul 21, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 celica and for some reason the front signals does not work at all. When I turn on the blinkers it blink really fast on both sides but hazard light works fine it blinks normal but it...


check the main earth wire near the battery. and one near the rear of the lights. unbolt them and clean the connectors up put some grease on them after. then check again. remember that when the earth wires come off the radio code will be needed to reset the the radio. be safe and take the battery off.

Sep 28, 2013 | Cars & Trucks

1 Answer

2000chevycavalier left turn signal don't blink and makes a buzzing noisr


its in the switch on the column. try pushing forward on the turn signal handle while turning the switch on and hold it there to see if it starts blinking .my 95 grand prix se has the same problem. i have to get a switch from a place call pull appart its a junk yard .

Jan 24, 2013 | 2000 Chevrolet Cavalier

1 Answer

On 2003 Kia Sedona, when there is moisture outside like rain or snow the signal lights don't work Properly. When apply brake right signal light comes on and does not blink, when turn on left signa


sounds like you are getting water into the connections and possibly have a bad earth connection. Suggest you check all light connections for water ingression.

Aug 11, 2017 | 2003 Kia Sedona

1 Answer

Directionals go on but don't blink


One side doesn't flash or both? Make sur ALL bulbs light up, try emergency flashers. If they work, probablt have a bad flasher relay under driver's side of dash. if not, may have a bad turn signal switch. They are well known for problems.

Oct 02, 2012 | 1995 Chevrolet G20

1 Answer

Turn signals don't work


did you change the light bulb

Mar 13, 2012 | 1994 Mercury Sable

1 Answer

How do i fix my blinkers on my 1971 f100 ford ?


There is a flasher unit for the turn signals, separate from the hazard flasher, that is under the dash. If the fuse for the turns is good, and you already know the bulbs are good since the hazards work, then you may have a bad turn signal switch.
When you use the turn switch, do the bulbs come on and stay on, or nothing? If they come on and don't blink, then it's probably a bad turn flasher unit. If they don't come on at all, suspect a bad turn signal switch. But first check the fuses, then pull off the connector to the turn switch and see if you have one hot wire there, with key on. That one hot wire will be from the fuse.

Mar 01, 2012 | Cars & Trucks

1 Answer

Turn signals on my 1992 Park Avenue blinked slower and now donot work at all. My emergency flashers work fine and all blink but I have no turn signals and nothing lights up when signal is left or righ


About your 1992 Buick Park Avenue 3.8L SFI OHV 6cyl. the Flasher is located:
Hazard flasher: Front seating area, driver side, under dash, mounted above kick panel

Turn signal: Front seating area, driver side, under dash, driver side of steering column, mounted on support bracket

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 11, 2011 | 1992 Buick Park Avenue

1 Answer

My turn signals don't work but my hazards are fine


try pushing, pulling, tugging on hazard switch button when turn signal is on, left or right, if they start blinking, the turn signal switch is bad.

Sep 14, 2011 | 1998 Ford Explorer

1 Answer

My turn signal will not blink, but my hazards work. ive replaced the 2-way flasher and it didnt work. what should i do?


I don't have your wiring diagram, but often, the turn lights and the flasher circuit use two different fuses, so it is not surprising that one would work and the other doesn't.
On a car this old, you are looking not only for burned fuses, but also corroded fuses. Pull the fuses out and examine them for corrosion, and clean their sockets.
Sometimes turn signals will not blink if you have a bulb out (insufficient current flow to trigger the blinker circuit) so if you have a bulb out on each side, that could cause both sides to fail to blink.

Aug 24, 2011 | 1992 Buick LeSabre

Not finding what you are looking for?
2000 Mercury Villager Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...