Question about 2000 Mercury Villager

1 Answer

Turn signal blinker dont show - 2000 Mercury Villager

Posted by on

Ad

1 Answer

You have never had that before with
any vehicle?
You check/turn on all parking & turn signal lamps
& replace the one that is burnt out
On the blinker the front or back may
light but not blink,that tells you the other
end is burnt out lamp

Posted on Jul 21, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 jeep wrangler 2.5


dont break the brakes..... TURNS & HAZ
many blinker, modules , internally flash with any load.
1: check all fuses first... (SOP)
2: then remove the blinker loads from the timer.

see it here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see WIRING, (end)
8w-51/52
chapter 8w, page 51-4 shows the switch. (complex it is)
note how brake and turns are shared, resources. (blub elements)
now 8w-52-6
see the flasher module.
see C305 pin 2, any load on that pin will cause it to flash.(inside)
that would be any switch in the combo switch stuck on.

Apr 07, 2014 | 1997 Jeep Tj

2 Answers

I have a 1992 Buick La Sabre Custom. My brake lights are not working but taillights, turn signals and hazard lights do work. Switch ok. fuse ok. ????????


if your fuse is good. and you have power at the brake light switch and when you hit the brakes you have power coming out the otherside of brake light switch/which would be the white wire/ check that the white wire is sending power up the turn signal switch. if theres power there and your turnsignals work? im afraid that your turnsignal switch is bad rare but it has been known to happen.

Jan 27, 2011 | 1992 Buick LeSabre

1 Answer

1990 Corsica: the brake lights work but the blinkers dont...


does the hazard signals work? if they do, then replace all turn signal bulbs.

May 06, 2010 | 1990 Chevrolet Corsica

1 Answer

Blinkers dont work but 4 ways work.


Check your turn signal fuse first, if the fuse is found good, replace the turn signal flasher.
I am assuming when you state the blinkers are not working that both the front and rear turn signals are not lighting at all.
Good luck.

Dec 05, 2009 | 1992 Ford Ranger

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

2 Answers

Right rear brake light and blinker dont work


when you use the right turn signal, does it blink faster?. Could it be the bulb holder is damaged or rusty?

May 16, 2009 | 2001 Plymouth Neon

1 Answer

Turn signals and back up lights dont work, bulbs and fuses good. Blinker lights only work in dash when emergency flashers are on.


Test the circuit board wires on the back side of your taillights where the bulbs go in to see if power is going there with the blinker on, if yes replace the circuit board (quite common with these trucks). If there is no power back there check your flasher relays for each turn signal, assuming they dont click off and on when you tip the turn lever. if all else fails, head for the multifunction switch behind your steering wheel inside the column that your turn signal/wiper/cruise control lever is connected to.

Mar 06, 2009 | 1991 Chevrolet C1500

1 Answer

Blinker dont work flasher and other lights work


The turn signals don't work, but the emergency flashers do? If that's the case, replace the flasher, you have 2 flashers, one for emergency (hazard) flasher, and one for the turn signals. It should be on the fuse block under the dash.

Oct 23, 2008 | 1995 Jeep Cherokee

Not finding what you are looking for?
2000 Mercury Villager Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...