Question about Ford F-250

1 Answer

Ford f250 4X4

Drifts right

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Get an alignment

Posted on Jul 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Right rear wheel bearing on 1986 Mustang GT bearing race unable to remove race.

The make a special tool to remove them or you can drive it out with brass drift punch and a hammer

Apr 28, 2018 | Ford Mustang Cars & Trucks

1 Answer

2000 ford explorer is in park but keeps drifting

your parking brake cable might be broken or you may need new pads i would have both checked

Mar 31, 2014 | 2000 Ford Explorer

1 Answer

Van drifts alot left to right

Hi and welcome to FixYa!

You may want to lift the car to check if you have worn out bushings, worn out wheel bearings or stabilizer links. If these parts are worn out the vehicle tends to wiggle or drift. There surely is no stability and can be dangerous. Have it checked and replaced if necessary.

Hope this helps and thank you for using FixYa! Have a good one!

Feb 21, 2011 | 1991 Ford Aerostar Extended

1 Answer

Need to remove cover arount stearing weel but ignition need to come out first how to take ignition out

There are 4 holes in the bottom of the steering wheel column cover. 3 of them are the screws you removed.
The 4th hole ( towards the ign cylinder ) is the release pin.
Turn the key to the Run position
Insert a punch or drift in the hole, while pulling out on the key, it should slide right out if you have the release tab pressed in far enough.

Sep 22, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

Escort drifts left to right

two possible problems...
1.) front end out of alignment
2.) brakes are dragging

Apr 02, 2010 | 1995 Ford Escort

1 Answer

My 2000 excursion wants to drift left and right i changed the sway bar arm from the stearing to the pitmant ard helped some but still does it

Tires play a big part in this,so do tie rod ends,and bar joints,hve them checked,sounds like a front end part about to come off.A alignment on the front end will have to be done anyway,so let them find the problem for you.

Nov 22, 2009 | 2003 Ford Excursion

2 Answers

My daughter has an 2000 ford excurtion. when she puts into park it will drift forward or backwards depending on the grade. What should I look for autum halloween. s halloween witch

Aug 26, 2009 | 2000 Ford Excursion

1 Answer

Removing the right intermediate axle shaft

i can only guess it is a 3.0l 4v well as far as the axle goes, the rh outer half shaft seperates at the splines on the intermediate shaft.
the intermediate shaft is the solid shaft from the trans to a bearing support bracket and ends after that. it is externally splined.
the rh axleshaft , inner cv joint, is internally splined.
to remove the rh axleshaft, remove the rh wheel and splash shield.
removed the lower balljoint pichbolt and seperate the lower balljoint front the steering knuckle. take the axle nut off and using a large brass drift or hardwood, drive the axle out of the bearing-hub assembly. DO NOT DAMAGE THE THREADS. also use some lubricant on the axle nut dissasembly. after the outer axle end is free, using the same brass drift or other, hit the inner cv joint and drive it off the intermediate shaft. inspect the splines closely because these fail and cause a no-drive condition.
then the mounint bolts for the support bearing and pull the intermedate shaft out, you will loose some fluid.

Jan 27, 2009 | 2003 Ford Escape

1 Answer

Front wheel bearing/tools

big spanners, or shifter, deep sockets, hammer, drift, screwdriver, and clean cloth. don't forget the bandaids,

Jan 27, 2009 | 1996 Ford F250 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides