Question about Cars & Trucks

Open Question

How to replace inner tie rod chevy malibu - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

justuscc
  • 360 Answers

SOURCE: replacing outer tie rod on a 2000 dodge neon

put the tie rod back in and thread the nut on. then you turn the inner tierod with a pipe wrench or a big pair of channel locks. you can spray the threads with pb blaster or wd-40. also if ya have a propane torch this helps loosen the threads. apply heat to the outer tierod do not heat the inner. good luck jimmy

Posted on Oct 03, 2008

  • 90 Answers

SOURCE: tie rod problem 98 Dodge

Yes, there's a special tool called an "inner tie rod tool". It has special crowsfoot type pieces that attach to a long tube with a 1/2' drive ratchet hole in it. First, remove the outer tie rod (COUNT THE # OF REVOLUTIONS WHILE UNSCREWING IT!!) Take off the jamb nut. Take the boot off. Use the tool to remove and replace the inner tie rod. Re-install the boot, jamb nut, and outer tie rod. If you count the # of turns it takes to remove the outer tierod, you'll be able to set it back where it was enough to drive it. i still recommend an alignment though.

Posted on Feb 16, 2009

chuck943
  • 783 Answers

SOURCE: 97 taurus GL inner tie rods

You have to have a special tool like this
http://motors.shop.ebay.com/items/Parts-Accessories_Automotive-Tools__W0QQ_nkwZfordQ20innerQ20tieQ20rodQ20toolQQ_fromfsbZQQ_trksidZm270Q2el1313QQ_odkwZQQ_osacatZPartsQ2dAccessoriesQ5fAutomotiveQ2dTools

Disconnect the outer tie rod and remove,then remove boot,then use special tool to remove inner tie rod. You will then have to have it aligned. You can use a tape measure to get it close enough to drive,just mark one of the grooves in the tire so you are measuring the exact same points,measure from tire to tire in the front of front tires then take a measurement at the rear of front tires and adjust the outer tire rods until the measurements are pretty close to equal.

Posted on Feb 17, 2009

  • 4369 Answers

SOURCE: How to change inner tie rod ends?

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Posted on Apr 15, 2009

Molson02536
  • 3854 Answers

SOURCE: how difficult to replace inner tie rod end on 06 silverado 2wd?

Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there Rack and pinion kit for a 1997 chevy lumina/driverside shaft lose.


There are inner and outer tie rods that can be replaced. The inner tie rod disconnects under the boot. They rent tools to get the inner tie rod off.

Jul 10, 2016 | Cars & Trucks

1 Answer

Replacing left side inner tie rod end


just unbolt it count rounds of taking the end off and screw new one on same amount will get you close on alignment

Apr 02, 2014 | 2004 Chevrolet Malibu Maxx

1 Answer

2001 chevy truck with rack and pinion drivers side inner tie rod do u need special tools to take off the rack


Yes you need an inner tie rod tool which is long and has several different sizes of connectors to apply to tie rod.

Jan 18, 2013 | Cars & Trucks

1 Answer

How to replace inner tie rods


Theres a tool that you need after you remove outer rod .slip tool over inner turn left with breaker bar
11_29_2012_8_39_54_pm.jpg

Nov 29, 2012 | 2002 Chevrolet Malibu

1 Answer

Where is the inner left and right tie rods at on a 2003 Chevy Silverado Just need to know exactly where they are


The inner tie rod ends are on the other end of the same rod as the outer tie rod ends. They should connect to the drag link and look almost identical to the outer tie rod ends. Hope this helps.

Sep 11, 2011 | 2003 Chevrolet Silverado 1500

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

1991 C1500: I am replacing the tie rods on my 1991 Chevy C1500...


The inner holes, the inner tierod ends go into the outer holes.

May 16, 2010 | 1991 Chevrolet C1500

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

1 Answer

How difficult to replace inner tie rod end on 06 silverado 2wd?


Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Jun 03, 2009 | 2006 Chevrolet Silverado 1500 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...