Question about Cars & Trucks

1 Answer

Hello I have a 2001 ford ranger edge an having problems starting at times a shop replaced switch an it still won't start at times they say the pass lock is reading but I believe it doesn't read at times if I take key out for awhile it want start if I put key in a let it sit awhile it will start how do I correct this problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 4,536 Answers

U need a data stream run to get values and voltages of the systems in the car--an independent shop can do it with pro equipment--at times just a sweep will cure it--get anothr mechanic not a dealer that knos what their doin------they may hav put switch in rong or its an aftermarket too---try anothr key-the chip on it may be worn

Posted on Jul 20, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing a 2004 ford ranger edge 4.0l


You will need specialized tools for this procedure. Certain timing alignments have to be performed be for installing some of the components. Get it to a shop that has those tools. Not for the home mechanic type of job.

Oct 02, 2016 | 2004 Ford Ranger

1 Answer

Put new selenoid and starter in 1992 ford ranger stx started up and now it won't start unless I pop start it


Have you checked the positive and negative connections at the battery, and are you getting voltage at the starter and solenoid when the key switch is in the start position ?
Have you checked the clutch safety switch ?

Jan 28, 2013 | Ford Cars & Trucks

1 Answer

I have a 89 ford ranger it won't start it acts


What have you checked so far ?
Is it getting spark to the plugs ?
Can you spray starting fluid into the throttle body and get it to start ?
Have you checked fuel pressure at the injectors ?

Jan 18, 2013 | Cars & Trucks

1 Answer

Engine turns over, but won't start.


No you can check the fuel pump relay, then the fuel pump for ground
& then replace it or have a shop do the job of finding the problem

Nov 24, 2012 | 2001 Ford Taurus

1 Answer

2001 Ford Ranger Edge clulch all the way to the floor


Replace the Clutch Slave Cylinder as a complete assy

Nov 23, 2012 | Cars & Trucks

1 Answer

'03 2.5L Ford Ranger Standard Trans, Engine at times won't turn over, does not click, battery is fully charged.


Neutral safety switch on the clutch pedal may be going out. Its a $15 fix. It tells the computer if the clutch is engaged. If it goes out its like trying to start with out pushing in the clutch, wont turn over at all. Hope this helps.

Oct 16, 2012 | 2003 Ford Ranger Regular Cab

1 Answer

Why does my 1985 ford ranger keeps dying or stalling out


Based on your info you should be able to duplicate the problem on demand.
When the engine won't start, you need to figure out if it is fuel or ignition related to proceed.
Check to see if the plugs are firing, and if not check the coil, and see if the carb has fuel in it.
Ford products built in the 1980s had problems with the ignition module mounted on the side of the distributor but you may have replaced it already.

Jul 20, 2012 | 1985 Ford Ranger

1 Answer

2001 Ford Ranger Starting Problem


I had this same trouble with other cars and it was loose connection in wiring harness at plug in the fuel pump circuit. The wire connector was loose in the plug and would not always maintain contact. The symptom on mine was it would die when I hit a bump sometimes, but ran fine at all other times. It finally quit entirely and had to hunt for it.

Jun 09, 2017 | Ford Ranger Cars & Trucks

1 Answer

I have a 1998 Ford Windstar. Got in to drive, turned the key to start and 'snap' something seems to have broke within the ignition lock cylinder... all of the accessories are on... the key...


This happened to to me with my ranger. I went and bought in ignition and a junk yard and no problems after that. That way your not out of a lot of money.

Jun 02, 2011 | 1998 Ford Windstar

3 Answers

4x4 does not respond at all on 2001 ford Ranger Edge


I have a 2001 Ford ranger edge 4x4 with the 4.0L SOHC. My 4x4 module had to be replaced before I bought the truck used. The previous owner said the module was located behind the plastic panel that is under and to the right of the glove box. Mine makes a clicking noise whenever I turn the switch to 4x4 or 4x2. That's just the solenoid switch that is inside the module working. From what I've heard it's pretty common for the modules to get corroded from moisture over time in that location. Hope this helps. God bless

Sep 17, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...