Question about 1994 Ford Ranger Supercab

Open Question

1994 ford ranger dash diagram how to remove?

Where are all the connection sites for the dash to the fire wall/

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

  • 341 Answers

SOURCE: what is the firing order for a 1994 ford thunderbird?

Firing order 1-4-2-5-3-6 ------- front | 1 2 3 | of | | vehicle | 4 5 6 | ------- Distributor rotates counter clockwise

Posted on Oct 22, 2008

johnny5846
  • 379 Answers

SOURCE: firing order diagram for 1986 ford ranger

you will find this site usefull , here is the diagram for 1986 ford ranger 2wd 2.9liter v6 firing order .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm


Fix Ya vote is my Reward , thanks .

Posted on Jan 08, 2009

  • 33 Answers

SOURCE: removal and install timing belt 1994 ford ranger/

Depends on the engine.

Posted on Oct 10, 2009

  • 2 Answers

SOURCE: 1994 ford ranger vacuum diagram

There should be a decal under the hood, 2 or 3 to be exact, vacuum routing, serpentine belt roouting, and a/c info.

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake line schematic 1994 ford ranger


That would be the Brake Service Light switch and it needs to be replaced.

Mar 15, 2015 | Ford Ranger Cars & Trucks

1 Answer

2002 Ford Ranger Extended Cab Heater Core Replacement


Not an easy job. Drop the steering column and remove the dash first. Then remove the plenum. Core is between the plenum and fire wall. Get a manual. Your saving hundreds doing it your self. 30 dollars for a manual is worth it.

Jan 26, 2015 | 2002 Ford Ranger

1 Answer

How to replace headlight switch 1994 ford ranger


take the dash apart so as you can get to the switch, unbolt and replace

Sep 28, 2012 | 1994 Ford Ranger Supercab

1 Answer

Where is the pc, lovated on a 94 ford ranger xlt 3.0


It is located under the hood on the drivers side fire wall, down low near the fender.

Apr 16, 2011 | 1994 Ford Ranger Supercab

1 Answer

I need a wiring diagram showing wiring from spark plugs to distributor for a 1994 ranger v6 3.0


Use the diagram below and just match up the colors of the cylinders to the distributor cap for proper firing order. So starting at the black dot on cap and moving to the right the next cylinder is 4 the 2 the 5 the 3 then 6.


emissionwiz_42.gif

Feb 17, 2011 | 1994 Ford Ranger Supercab

1 Answer

Need to see diagram for 1994 3.0 ford ranger firing order


1994 Ford Ranger 3.0 liter V-6 VIN "U"

14032f9.gif


Hope this helps (remember to rate this).

Oct 20, 2010 | Ford Ranger Cars & Trucks

1 Answer

How many Oxygen sensors in Ford Ranger 1994


There are 2 O2 sensors on your Ford Ranger.  There will be one a foot or two before the catalytic converter and one a foot or two after the converter.  I don't have a diagram but you will only need to look for the identical sensor located up or downstream from the first one that you replaced.

May 16, 2009 | 1994 Ford Ranger Supercab

1 Answer

Firing order on a 94 ford ranger 3.0


Sorry, that supposed to be under solutions.a79bdf6.jpg

Mar 26, 2009 | 1994 Ford Ranger Supercab

1 Answer

Firing order diagram for 1986 ford ranger


you will find this site usefull , here is the diagram for 1986 ford ranger 2wd 2.9liter v6 firing order .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm


Fix Ya vote is my Reward , thanks .

Jan 08, 2009 | 1986 Ford Ranger 2WD

1 Answer

Ignition wiring


firingorder6a.gif firingorder6.gif 1991-1994 2.9L and 3.0L Engines Firing Order 1-4-2-5-3-6 1995 And Later 3.0L V-6 With DIS Ignition System Firing Order 1-4-2-5-3-6
4.0L Engines Firing Order: 1-4-2-5-3-6 DIS Ignition System

Nov 22, 2008 | 1995 Ford Ranger Supercab

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...