Question about Cars & Trucks

Open Question

Where is the Ford Bantam crank sensor position

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

carsandcomps
  • 722 Answers

SOURCE: crank position sensor error 11

Well, being this is v6, take off the fan, and the belt. Since the crankshaft is at the bottom of the engine, the sensor will be located near it at the front of the engine, on one side or the other. It will have a wiring harness connected to it, and should be mounted to a small bracket. It's best to remove the entire bracket, especially if the new unit came with a new one. Use BOTH new parts. Do not adjust timing at all until the sensor has been replaced.

You may need a "feeler gauge" to set this, as they (on some vehicles) need to be spaced at a particular distance from the harmonic balancer (if and external sensor). This I believe is and internal, so you should be fine simply inserting it in place.

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

Posted on May 22, 2010

  • 3640 Answers

SOURCE: ford bantam cant crank or

check all fuses first ... if that doesn't help, disconnect both battery cables and leave disconnected overnight .... sometimes that will reset the system (i know for a fact it will on dodge and chrysler and i have heard it will on fords too). have a good day !! if above does not work, go to this site. it should help you. www.asashop.org/autoinc/jan2008/techtips.htm have a good day !!

Posted on Jan 10, 2011

SOURCE: Hi i have 2004 1.6 ford bantam rocam that wont start, all the dashboard light come on but thats it! Checked all the normal suspects, new starter, battery all fuses check and replaced the crank angle s

firstly,check that the car has spark and petrol,from there you can be assured that it is a electrical problem

Posted on Jul 13, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS SYMPTOMS OF ILL OPERATING DISTRIBUTOR.WHAT IS THE CORRECT SPARK PLUGS FOR 2002 FORD BANTAM 1.6I .SHOULD I USE COPPER WIRE OR CARBON PLUG LEADS.


using a timing light, watch the light on the timing mark and if it is all over the place and not steady on the mark then that indicates a worn shaft and bushes in the distributor
use carbon resistance plug leads that have thick insulation( (not el-cheapo leads ) modern plugs are designed to run carbon leads
run the fault codes as the problem may be in the air /fuel control sensors and not the distributor or crank. cam position sensors

May 07, 2017 | Ford Cars & Trucks

1 Answer

Hi My Ford bantam diesel does not have power it can only reach 110 km per hour, my ref count go anywhere more than 3, please advice on what could be coursing the problem


run the fault codes and look for problem accelerator position sensor
may be an EVAP not venting the fuel tank properly

Nov 09, 2016 | Ford Cars & Trucks

1 Answer

Where are the speed sensor situated on a Ford Bantam 1.6 rocam


It is plugged into the transmission where the speedo cable would go in older cars.

Jun 22, 2016 | 2008 Ford Bantam 1.6i

1 Answer

What causes the cooling fan to operate non stop/ kicking in very often?


The temperature of the coolant (mixture)... is monitored by a thermostat... which then activates the cooling fan...

It is most likely in a ten year old car... that the cooling system has NEVER BEEN serviced... and more likely the FAN and Temperature sensor are the early warnings of a major cooling system failure.

Check your pump, hoses, fluid levels...for any obvious signs of leaks...

Invest in a pressure tester (see below) and test the integrity of your system... before buying that new anti-freeze.

Hope this helps

http://aideyouhuo.net/freereadbook-pdfonline/ford-bantam-2006-manual.pdf

http://www.manualspath.com/get~workshop-manual-bantam-2006.pdf

http://waterstoneaesthetics.com/ebook-name/f/ford-bantam-2006-manual-.pdf

May 06, 2016 | 2006 Ford Bantam 1.6i

1 Answer

I have a ford bantam 1.3 rocam i replaced the clutch and im not getting spark or fuel coming through! I replaced the crank sensor and had the ecu tested and still nothing it just cranks over!


First is check fuses, replace them and then recheck. Next would be to make sure you didn't pinch an electrical line/harness. Next check grounds. Next get the codes. After this would be checking continuity of wires.

Mar 03, 2016 | Ford Cars & Trucks

1 Answer

My 2008 Ford Bantam seems to have strange firing order 1-2-4-3? is this correct. Also the distributor does not have an H.T. lead. Can someone help please?


4 cylinder engines can have both firing orders
the more common one is 1-3-4-2 but some manufacturers have the other firing order
it depends on the manufacture of the position of the crank pin
some reason for it are
less harmonic vibrations
less stress on crank webs
easier manufacturer
for the missing problem run the fault codes and check for ambient temp sensor , maf/vaf sensor or BARO sensor problem

Dec 31, 2015 | 2008 Ford Bantam 1.3i

1 Answer

Why is my ford bantam 1.3 cranking but not starting?


probably the immobilizer has been activated
check fob key battery
reset the immobilizer using a scan tool on the ECM

Oct 09, 2015 | Ford Cars & Trucks

2 Answers

I have ford bantam 1.6i rocam 2006 model. It Doesn't start, It doesn't pump the petrol, the is no power to fuel pump


Refer to your manual there is a switch that deactivated the fuel pump in case of accident, there is a switch by the pasangers feet that if in the up position is activated to stop the fuel...

Aug 28, 2012 | 2006 Ford Bantam 1.6i

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...