Question about Chevrolet Cars & Trucks

Open Question

Door seal leaks on a 2010 chevy malibu front passenger side& both rear doors

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 74945 Answers

SOURCE: rain water leak

The most common source of this kind of leak is the windshield, have a glass shop check the sealing around the glass

Posted on Sep 04, 2008

emissionwiz
  • 74945 Answers

SOURCE: Single power door lock does not work

If it doesn't work from master switch then the door lock motor actuator will need to be replaced, this requires pulling the door panel.

Posted on Sep 20, 2008

  • 110 Answers

SOURCE: very loud wind noise around R/F passenger door

wind window down hold top of door frame put your knee on door and pull frame towards you this will give a tighter seal

Posted on Nov 18, 2008

SOURCE: how do you remove the door panel?

All GM's cars and trucks are relatively the same. U just need a few tools to remove the panels without damage. one is a tool called a button popper.
1. there will be a screw inside where the door handle is. u need to remove this .
2 starting from the top left go around the outside the panel to see if there and screws holding the panel on.
3. starting with the bottom left insert the tool and lift up on the panel. u should here a pop when u lifted it enough. next goto to the bottom right. and do the same thing.
4. grab both bottom pats and gently outwards.. if its not popping as u are pulling the panel dont force it to do it. check to make sure there are no other screws hidden anywhere. (inside little plastic covers. the center area) repeat the procedure
5. when the panel is loose, pull out slightly and push upwards. this will separate the panel from the door and glass.
u can then see where the electrical connections are and complete the part u are doing.

Posted on Apr 21, 2009

  • 3 Answers

SOURCE: 1997 BMW 528i The passenger side front and rear doors won't

I had the same problem on the rear door of my 1998 528i and it was the door actuator that had gone bad. I had to take the rear seat out to get the door panel off. Once I had the door panel off it was not that difficult to replace the door actuator.

Posted on Jul 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 chevy lumina euro and recently while raining the passenger side front and rear carpet is getting wet,can't find where the water is coming from. All window seals are fine. Any idea why?


possible that the water is getting into the car from a failed membrane that seals all the openings under the door trim and /or the drain holes at the bottom of the doors are blocked
fix is to clean out the drain holes and remove the door trim and reseal the plastic back around all the openings in the inner door frame

Jan 19, 2017 | Cars & Trucks

1 Answer

How do I replace inside door handle passenger side on a 2011 GMC Terrain?


Search Results

    How To Install Replace Inside Door Handle Chevy Equinox ...

    ? 9:02
    https://www.youtube.com/watch?v=cY6asyM2R6g
    Feb 2, 2012 - Uploaded by 1A Auto Parts
    How To Install Replace Inside Door Handle Chevy Equinox 05-09 1AAuto.com .... found your tutorial on fixing my driver's side door handle for my 2006 Equinox. .... Door Handles Chevy Equinox 2010 2011 2012 GMC Terrain ...

    How To Install Replace Inside Door Handle 2007-13 ...

    ? 9:05
    https://www.youtube.com/watch?v=QonKLwhk2CE
    Apr 2, 2015 - Uploaded by 1A Auto Parts
    http://www.1aauto.com/interior-door-handle-driver-side-front/i/1adhi00417 1A Auto shows you how to repair, install, fix,change or replace a broken or snappe... ... 10, 11, 12, 13 Chevy Silverado, Tahoe, Suburban and GMC Sierra, Yukon Denali ...2007-2011 Tahoe Yukon Suburban Escalade Vent Section ...Missing: terrain

    How To Install Remove Rear Outside Door Handle 2007-13 ...

    ? 10:02
    https://www.youtube.com/watch?v=7ZUTqqEzpZg



Feb 08, 2016 | GMC Cars & Trucks

1 Answer

Water on front & rear floorboards of 2004 Chevy Aveo


it is getting in from somewhere run water over the car using a garden hose and you will find it.look for where its wet at the highest point and thats probably the spot.

Jun 05, 2012 | Chevrolet Cars & Trucks

1 Answer

Hi there ..I just got a driver side window motor,to replace my old one in my 99 Chevy Malibu..whats the steps to take to take off the old one and place the new ??


GM Malibu/Cutlass 1997-2000 - Repair Guide

Window Regulator And Motor Assembly
REMOVAL & INSTALLATION

Rear Door


4f4e997.gif
Fig. The rear window regulator is an assembly that consists of two pieces

NOTE The front window regulator is removed as an assembly with the door control module. Refer to the procedure outlined in this section under Door Locks.
  1. Remove the door panel and the water deflector.
  2. Remove the door glass (window).
  3. Detach the electrical connector, if equipped, or remove the window regulator handle.

To install:
  1. Install the window regulator.
  2. Place the regulator through the rear access hole into the door.
  3. Attach the electrical connector, if equipped, or install the window regulator handle.
  4. Install the rear side door window.
  5. Replace the door window assembly.
  6. Install the water deflector and the door panel.

Door Locks
REMOVAL & INSTALLATION

Door Control Module


882bea7.gif
Fig. The door control module contains the door locking system module and the power window system module
  1. Raise the window to the full up position.
  2. Remove the inside door trim panel. Refer to procedure outlined in this section.
  3. Pull off the plastic film water deflector enough to access the lock actuator.
  4. Remove the screws securing the door lock actuator.
  5. Remove the door locking system module nuts and bolt.
  6. Remove the door locking system module from the door.
To install:
Installation is the reverse of removal, but make sure to tighten the fasteners to the torque specifications listed:
  1. Door locking system module bolt-89 inch lbs. (10 Nm).
  2. Door locking system module nuts-89 inch lbs. (10 Nm).
  3. Door lock actuator screws-53 inch lbs. (6 Nm).

Hope helps (remember rated this) Good luck.

Jan 21, 2010 | 1999 Chevrolet Malibu

1 Answer

My 2004 1.4 Polo keeps getting really wet inside, and today i noticed mould on the back seat where everything is so damp. Could it be a clogged drain? If so, how do i get to it?


lift the spare wheel out of the car there is a drain plug under it.

also its more likely to be leaking through the rear lights or rubber seal around the doors or boot. I have a golf was leaking from the back passenger door. and the front passenger side. back was the door seal and the front was a drain plug that was clogged up lift the bonnet and look around the bulkhead/ thats the part closest to the windscreen where the wipers are loacted, look right down it for any leafs etc.

Jan 15, 2010 | 2004 Volkswagen Golf

1 Answer

How remove rear door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Feb 20, 2009 | 1999 Chevrolet Malibu

2 Answers

There is a water leak somewhere in my 98 toyota camry that leaks into my passenger side floor. There is no sun roof and no visible leaks from the windows or doors. Any thoughts? A/C leak maybe? water...


I am the original owner of camry xle 1998 with wet floors. In 2000 I had drivers side door seal leaking at welt. Removed old door seal and new weather strip on drivers side installed. The door panel was never wet, but wet at bottom of door where there are drain holes...slowly leaking under carpet.
In 2001 later water again. Coming from overflowing A/C evaporator-drain plugged/ tank full of debris. Removed evaporator, cleaned + drain cleaned.
In 2003, driver door seal against window rotted. Removed door panel and found leak at window belt molding at the mirror joint inside + out. Lots of mold under carpet needed to replace! Made a fuss at dealers for reacurring problem and they replaced the carpet for free.

Sep 07, 2008 | 1999 Toyota Camry

1 Answer

Rain water leak


The most common source of this kind of leak is the windshield, have a glass shop check the sealing around the glass

Sep 04, 2008 | 1992 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...