Question about Cars & Trucks

Open Question

How to remove the glove box on my 05 Malibu - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jj127
  • 37 Answers

SOURCE: Removing the glove compartment & replacing the blower resister.

You do not need to remove the glove box to get to the resistor its located at the very bottom of the dash. Its held in by 1 or 2 screws. If you already bought the replacement look for the same thing underneath, a flashlight helps. Fairly simple, just have some patience. Its close the the blower motor.

Posted on Jun 20, 2009

Ad
  • 3600 Answers

SOURCE: vent door stuck and can't remove glove box

why can't you remove the glove box? You can get at the door from under the dash but it's a ***** to do. try lubing the vent cables unless it uses the vacuum motor, if it uses the vac. motor it will be hard to get to without the glove box being out.

Posted on Jan 05, 2010

Testimonial: "Thanks! I just don't know how to remove the glovebox."

  • 118 Answers

SOURCE: how to change fuses in 2006 chevy malibu

Use the supplied fues puller or a needle nose pliers and pull the old one out and press the new one in. Very simple

Posted on Mar 09, 2010

  • 8404 Answers

SOURCE: I have no key to open the glove box for me 1997

The lock will have to be picked. If you do get it picket, you will have to replace the lock or have a locksmith make you a new original. Expect to pay about $100.00 or more for this service.

There is that possibility that your local Chevy dealer can duplicate your key based on your VIN ... be worth a call to find out. You will have to prove ownership to get the key if they are able to make it.

Thanks for your interest in FixYa.com

Posted on Oct 03, 2010

emissionwiz
  • 76630 Answers

SOURCE: glove box removal

Remove the screws around the inside edge of the GB liner and just work the liner out.

Posted on Jun 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the ac/heat mode actuator on a 2005 malibu


its behind the glove box up and to the left after you lower or remove your glove box. Glove box has two little arms you can push inward and drop the glove box down nearly to the floor..

Apr 06, 2014 | 2005 Chevrolet Malibu

1 Answer

05 malibu heater vents blowing incorrectly


The are two controls on the heater. One is the blend door and that controls hot and cool, the other is the mode selector door and that changes the place air comes from. You should be able to see those and the area that controls the air in the plenum. The plenum is behind the glove box. Open the glove box all the way and see if the controls are visible. Activate the mode control to see if the lever moves on the plenum, the problem could be anything from a broken lever, bad control, loose control, or something that fell down the defrost vents.

Feb 20, 2014 | 2006 Chevrolet Malibu

1 Answer

Remove golve compartment on 1999 chevy malibu


There's only so many screws that hold the glove box in. Some are inside the glove box and some are underneath. You may need a torx wrench depending on the type of screws holding the glove box in.

Feb 18, 2013 | 2000 Chevrolet Malibu

1 Answer

2000 malibu blower wont run on hi will run on 1-4 what could be my problem?


usually its the fan resistor causing this. it is located behind glove box on top of heater box, beside the fan. the resistor has differant size wires for differant fan speeds. if a wire in resistor is bad. that fan speed will fail. when fixing, the best way is to remove glove box so you dont have to stand on your head to work on it. have a good day !!

Jun 24, 2011 | 2000 Chevrolet Malibu

1 Answer

Want to change blow motor resistor in a 2000 chevy malibu. How do I get to it?


remove panel from beneath glove box, you will see ecm just slide it to the side. now you should be able to see the fan. resistor is beside it!! remove connection then remove resistor. ( it may save on your back just to remove glove box. about 8 screws! ) have a good day !!

Oct 30, 2010 | 2000 Chevrolet Malibu

1 Answer

How do you fix a fan sensor in a 2000 malibu


are you talking about heating fan resistor! if so, this is where and how its replaced. it is behind glove box. remove glove box so you do not have to stand on your head, only about 7 or 8 screws. then loosen and slide ecm to one side. ( but when removing glove box, remove insulator panel under glove box first ) now you can see heater blower and resistor. it is beside the fan, remove the wires from it. take out holddown screws, then pull it out. have a good holiday!!

Oct 08, 2010 | 2000 Chevrolet Malibu

1 Answer

I need a layout for the resistor for the a/c fan speed control in a '99 Malibu


I do not have the diagram for you. but i can tell you how to change it! first, its behind glove box. to make things easier remove the glove box. remove insulating pad from underneath glove box, next loosen and slide the ecm to one side. now you can see resistor and blower motor. resistor is beside blower motor. remove wiring to resistor. take out the screws that hold it in. then pull it out of heater box. have a good day !!

May 17, 2010 | 1999 Chevrolet Malibu

2 Answers

How do i replace honda accord 05 interior air or inside cabin fil


Hello twodoxies.

Open the glove box. Remove the damper from the glove box then let the glove box hang down.
Remove the dust and pollen filter assembly from the evaporator case.
Remove the filter from the housing, and replace the filter.
Here is a picture to help you.

84744b2.gif

There you are. Thank you for using FixYa .

KL

Apr 30, 2010 | 2005 Honda Accord

1 Answer

Replace blower motor resistor unit on 99 Malibu ?


the blower motor resistor is below glove box. remove panal under box. slide the pcm out of the way, resistor is beside blower motor. unplug wiring, take out screws holding it in then pull straight out to remove.

Jul 10, 2009 | 1999 Chevrolet Malibu

1 Answer

Removing the glove compartment & replacing the blower resister.


You do not need to remove the glove box to get to the resistor its located at the very bottom of the dash. Its held in by 1 or 2 screws. If you already bought the replacement look for the same thing underneath, a flashlight helps. Fairly simple, just have some patience. Its close the the blower motor.

Mar 05, 2009 | 2000 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...