Question about Cars & Trucks

Open Question

Mazda proceed 1992. How do we remedy leaking fuel injectors please.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 196 Answers

SOURCE: Fast fule leak at injectors

Well it sounds like the leak is at the right rear of the engine as you face it if so right back by the fire wall is where the fuel lines couple together if you take the lines apart there should be a o-ring on eack line check that out and see if that is where the leak is

Posted on Jan 18, 2009

  • 6 Answers

SOURCE: how do i fix a fuel leak at top of injector on 7.3l 1992 f250?

Either your lines arent pressuring up and its pushing fuel back out the injectors or the o-rings on the injectors are bad. I had the same problem...I replaced the o-rings and it fixed it!

Posted on Jun 09, 2009

  • 14036 Answers

SOURCE: I ran my 1992 mazda

SOUND LIKE FUEL PUMP DAMAGED BECAUSE LACK OF FUEL. FUEL IN TANK.FUEL KEEP FUEL PUMP COOL AND LUBRICATED IF FUEL TANK GET TOO LOW OR EMPTY CAUSE FUEL PUMP OVER HEAT DAMAGE.

Posted on Nov 06, 2010

  • 1403 Answers

SOURCE: changed fuel lines on 1992 f 250 7.3 liter idi was

sounds like you're gettting alot of fuel pressure now for sure,you may have to pull those injectors and replace the 'o' rings around them,they may have been bad all along and not enough fuel pressure to make them leak.when you replaced those fuel lines did you pull on the injector rack at all? if you did, the solution is simple,push the fuel rack back down to reseat those injector 'o' rings. that should solve it. otherwise your stuck pulling that fuel rack anyway so i would try pushing that rack down either way. it may seal the injectors back up. hope this helps and thank you for choosing fixya.com oncallmech

Posted on Jan 10, 2011

  • 101 Answers

SOURCE: 1994 mazda 929 rough idle & stalling

Sometthing to think about. When it is cold the engine it runs in close loop, after it warms up it gos to open loop.

Posted on May 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cylinders 1 and 2 are misfiring causing major vibration and engine shut off while idling...is this a fuel injector problem?


This could be an ignition coil, spark plug, fuel injector or mechanical problem. You will need to isolate the issues and proceed accordingly. I would do some swapping arround. Swap the spark plugs 1 and 2 with m# and four and see if the misfire follows if it does you need plugs do the same with the coils again if the probles switches cylinders replace coils. if not then you may have to llok at injectors, compression and so on but I would try swapping things first

Oct 26, 2012 | 2001 Mazda Tribute

1 Answer

My mazda 6 keeps cutting out at junctions


could have clogged fuel injectors,could have intake leak,bad faulty fuel injector,weak or failing fuel pump, bad spark plug or bad ignition coil, many things will cause vechicle stall out at junctions.

Sep 18, 2012 | Mazda MAZDASPEED6 Cars & Trucks

1 Answer

1994 mazda 929 rough idle & stalling


Sometthing to think about. When it is cold the engine it runs in close loop, after it warms up it gos to open loop.

May 15, 2012 | 1992 Mazda 929

1 Answer

Mazda mx6 1992 wont start and plugs getting very wet, prior to this problem was running fine. too much fuel getting in? plugs sparking ok.


Hi Mike,
Sounds to me as though you have one or more injector leaking. First advice is to check the oil in the sump. You may find that the fuel has leaked past the piston rings and contaminated the lubricating oil. Please make sure you check that out as when you replace the injector(s) and start up, if the oil is contaminated the engine may knock!
Best regards Johngee10

Mar 08, 2011 | Mazda MX-6 Cars & Trucks

1 Answer

Changed fuel lines on 1992 f 250 7.3 liter idi was old slow leak . now all m,y injectors are leaking right above big nut on the injectors looks as if its coming up from bottom of injectors ... real crazy...


sounds like you're gettting alot of fuel pressure now for sure,you may have to pull those injectors and replace the 'o' rings around them,they may have been bad all along and not enough fuel pressure to make them leak.when you replaced those fuel lines did you pull on the injector rack at all? if you did, the solution is simple,push the fuel rack back down to reseat those injector 'o' rings. that should solve it. otherwise your stuck pulling that fuel rack anyway so i would try pushing that rack down either way. it may seal the injectors back up. hope this helps and thank you for choosing fixya.com oncallmech

Jan 10, 2011 | 1992 Ford F250

1 Answer

I ran my 1992 mazda marvie proceed out of fuel and suspect that the carb and injectors may be blocked, have replaced fuel filter but it still wont run or idle.Need to know how to strip and clean carb, etc


SOUND LIKE FUEL PUMP DAMAGED BECAUSE LACK OF FUEL. FUEL IN TANK.FUEL KEEP FUEL PUMP COOL AND LUBRICATED IF FUEL TANK GET TOO LOW OR EMPTY CAUSE FUEL PUMP OVER HEAT DAMAGE.

Nov 06, 2010 | Mazda B2600 Cars & Trucks

1 Answer

Mazda B2600i


are there any fault codes present? i was looking at the fuel injection diagram on autozone.com and the only thing i can see that controls injector pulse width is the pcm. are all the injectors open for 15ms? you should also check fuel pressure. if you want to look at the diagram, go to autozone.com. register and enter you car. select repair guides, chassis electrical and the wiring diagrams

Mar 30, 2010 | Mazda B2600 Cars & Trucks

1 Answer

How do i fix a fuel leak at top of injector on 7.3l 1992 f250?


Either your lines arent pressuring up and its pushing fuel back out the injectors or the o-rings on the injectors are bad. I had the same problem...I replaced the o-rings and it fixed it!

Mar 28, 2009 | 1992 Ford F250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...