Question about Cars & Trucks

Open Question

My BMW come up with code 2782 n 277f I v change t sensor n still it won't start plus it showing t same problem what can I do next

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1212 Answers

SOURCE: My 1999 Grand Prix GTP won't start after changing

Double check the wiring harness to make sure it did not get pinched under the manifold or the top cover. It is common for a single wire to get pinched and shorted and cause this.

Posted on Oct 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought my BMW at scrabyard they told the problem is sensor pully and the machenic put the sensor but still not want to start


check that the immobiliser is operational or the key fob battery is good. run the fault codes to check for other faulty sensors.

Dec 25, 2014 | BMW Cars & Trucks

2 Answers

98 blazer 4.3 engine won't start code p0336, already replaced crank sensor


which crank sensor do you replaced ? the P0336 means P0336 Crankshaft Position Sensor A Circuit Range/Performance.

________________
autel maxidas 708

Feb 25, 2013 | 1998 Chevrolet Blazer

1 Answer

1999 chevy k2500. changed spark plugs 4 times in 7 months. Runs good for a week then doesn't start. Changed spider, throttle body sensor. Still has no codes and once again won't start.


The next time it won't start ,pull a sparkplug wire and see if you're getting fire.Then we'll known whether its a ignition or fuel problem and go from there.

Jan 11, 2012 | 1999 Chevrolet K2500

2 Answers

Low or no power, changed the mass air flow sensor? OBD showed a problem on left side cat converter? Runs good one day and bad the next. Problem started after hurricane. Acts like exhaust is plugged ...


If its showing a catalytic converter code,,dont keep replacing other sensors..Has nothing at all to do with the map or the mass air flow sensor...Likely its the cat is clogged..That code tells you that your cat is not doing its job..I would change that cat on that side,,and quit letting the mechanic throw parts on the car..Thats to expensive

Sep 24, 2011 | 2000 Buick Century

1 Answer

1994 BMW 740i with 222,000 turns over but won't start. Removed battery, had it tested and it's good; radio, lights, windows all working fine. Driving the car on Friday, went to start it on...


Hi.

If it does turn over and electrical works, then the problem is unlikely the battery. You can try jump starting. If it cranks when jump-starting it may be a weak battery, starter motor or alternator, but I don't think that this is the problem.

Check if there is spark on all cylinders. Do a code scanning (this car is OBD1, you will need to do the scan at the dealer place or to find a BMW OBD1 tool- Universal OBD2 scanner will not work on a 1994 BMW). If the codes return misfire or mixture related errors check fuel pressure, check sensors and parts that determine the mixture (MAF/MAP, AIT, O2 sensors, IAC and EGR system), check the vacuum system for leaks and check the crank sensor.

Regards.

Ginko

Aug 08, 2011 | BMW 750 Cars & Trucks

1 Answer

P1320 code appeared and we replaced the cam position sensor. It ran OK, but started rough until warm and next code showed #1 cylinder misfire. Replaced #1 coil and it ran great. Then later the engine light...


i just had the same problem in my bmw 325i. Probably vaccum leak or exhaust leak. Check that nothing came loose in these areas. It takes time for your car to learn the new CPS (cam pos. sensor) so give it a few days and reset the code again and see if it works.

Mar 12, 2010 | 2000 Nissan Maxima

1 Answer

Just had my back brakes,rotos and sensor changed on my 2006 330I BMW and brake light and car lift light came on. Can't get it off. Help


Sounds like the sensor has defaulted.

Normally you would use a code reader to clear fault codes.

That is an option, but sometimes disconnecting the battery for a short period of time allows a reset of sensors upon re-connection.

If a shop did it, not a bad idea to call them and make them aware.

Plus they shouls offer to use their code reader to clear any faulty codes at no charge, being its vey likely associated with the work they just did.

If they don't, switch repair facilities.

Oct 02, 2009 | BMW 330 Cars & Trucks

1 Answer

BMW 328 i 1997: Start up problems / Stuttering / Engine Light


change the pcv valve its under the intake manifold

Feb 18, 2009 | 1997 BMW 328

2 Answers

328 i 1997: BMW Start up problem: Stuttering


it sounds like the cat is blocked,

Feb 17, 2009 | 1997 BMW 328

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...