Question about 2007 Chrysler Sebring Sedan

1 Answer

Where is thewater pump located - 2007 Chrysler Sebring Sedan

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Chrysler Master
  • 21,873 Answers

Duplicate question

Posted on Jul 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace thewater pump

How To Change A Waterpump - YouTube

? 2:19
Apr 6, 2010 - Uploaded by Scotty Kilmer I was wondering if it's a massive pain to replace the water pumpon a .... Is it possible for a water pump to only leak when a certain RPM is hit ...

Sep 25, 2015 | 1991 Buick Skylark

1 Answer

How do you replace the water pump?

Hello, ramrodsc2 Removal Procedure 1. Drain the cooling system untilthe coolant is below the level of the water pump. 2. Remove the drive belt guard. 3.Loosenthe waterpump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulleybolts and remove the water pump pulley. 6. Remove thewater pump bolts then Remove the water pump. 7. Remove the water pump gasket 8. Clean the water pumpmating surfaces pay particular attention to the cleaning process and make surethe surfaces are clean. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump; tighten the bolts to 10 Nm (89 inchlbs.). 3. Install the water pump pulley.Loosely install the mounting bolts. 4. Install the drive belt; this will help hold the pulley thentightening the pulley bolts. 5. Tighten the bolts to 25 Nm (18 inch lbs.). 6. Install the drive beltguard. 7. Fill the cooling system. 8. Inspect the cooling system for leaks. Regards, netvan

Mar 13, 2011 | 1999 Chevrolet Venture

1 Answer


Only if you have first checked that the thermostat is Ok and there is no blockage in the radiator. You can usually tell if the thermostat opens as the top hose gets very hot and the temperature dips.What was the basis for the water pump diagnosis? Maybe it's a common failure but I would want to know if the stat was opening first. You can check it by putting it in a pan on the stove with a thermometer and see what temp it opens, usually about 85-90 degrees
I hope I have been of help but please do not hesitate to ask if you have any further questions.
I appreciate your vote if you appreciate my reply.

Feb 28, 2011 | 1989 Ford Econoline

1 Answer

Leaking anti freeze but not from the hoses coming from the radiator

could be thewater pump leaking or the heater core more than likey its the water pump

Sep 05, 2010 | Honda Accord Cars & Trucks

1 Answer

How do you install a power steering belt on a 2000 Hyundai Accent? specs; 1.5l I4, sohc, 5 spd manual.

hi from uk easy enough job first disconnect battery earth lead then there is a slotted bracket thet is like on alternator adjuster using 12 mm spanner open end slacken off the bolt that is just behind thewater pump pully then the mounting bolt for the pump you can see below the pump ? slacken this now if you pull up the belt it will slacken and you can remove it this belt is small as it drives the p/steer pump from the outer pully of water pump fit new belt ensuring it fits correctly in grooves ? now using a suitable bar / flat tyre bar suitable position bar between p/steer pump and its mounting bracket that is bolted to side engine block lever gently to tighten belt and whilst holding bar leverage with belt adjusted ? tighten the adjuster slide bolt release bar and recheck belt tension ? retighten the lower mounting bolt also 12 mm job done! hope this helps ? ps you do not say if you have A/C but this is run of crank pully to a/c pump so no problem

Nov 12, 2009 | 2000 Hyundai Accent

2 Answers

Everytime I add coolant or water it instantly leaks bach out under the SUV. It trickles down the oil pan to the ground. Is this leaking from the water pump?

betya booties is is the water pump.try adding water while engine is running ,if the rate of leakage seems less ,it is definately the water pump. iwould take it to a radiator repair shop andthey will check for sure i doubt they will charge you as it only takes aminute , good luck.

Aug 01, 2009 | 2006 Kia Sorento

3 Answers

Fuel pump relay location

Hi irvj6ohn:
The 1993 and 1994 XJ6 Fuel Pump Relay is located in the trunk of the vehicle on the right hand rear side. It is light blue and black in color.
I hope this helps.


Oct 04, 2008 | 1993 Jaguar XJ6

Not finding what you are looking for?
2007 Chrysler Sebring Sedan Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides