Question about Cars & Trucks

Open Question

Bleeding brakes on 2009 dodge grand caravan

What order do you bleed them?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: can't find where/how to bleed back brakes 2000 dodge grand caravan

The problem isn't at your brake calipers. Your rotors have a slight warp to them causing your vibration when you stop.

Posted on Sep 01, 2008

Ad
  • 158 Answers

SOURCE: Can't find port to bleed front brakes 1995 Dodge Caravan

should be a bleeder screw on each caliper, unless, they were broken off in a previous attempt? They have to be there

Posted on Apr 07, 2009

  • 139 Answers

SOURCE: bleeding brakes

always bleed front driver side first, front right,left back
right back.
make sure you always have oil in the master

Posted on Apr 09, 2009

techbuster
  • 5081 Answers

SOURCE: bleeding brake system how?

BLEED BRAKE SYSTEM

Make sure one end of the Jeep is raised (starting with the rear end) and secure on jack stands and the wheels on each side have been removed. If you have been working on the brakes, this should already be done.

Connect a clear rubber tube to the bleeder valve on the right rear brake caliper. Start with this end and side because it is farthest from the master cylinder.Place the tube's other end into a container partially filled with brake fluid.

Open the bleeder valve on the caliper and have an assistant press on the brake pedal inside the Jeep. Look for a mixture of air and fluid to come out of the valve. Once all the air is purged and the fluid runs cleanly from the valve, close the screw and remove the tube.

Repeat the process for all four brakes. Move to the left rear next, followed by the right front and the left front. If you need to, reconnect the Jeep's rear wheels and lower the rear end before raising the front end and removing those wheels.

Check the level of fluid in the master cylinder periodically as you bleed the brakes. If the level drops below the needed fill line, add more fluid. Use fresh fluid, not any that you have bled from the brakes.

Start the Jeep's engine after bleeding all the brakes and press on the brake pedal. You might need to do this repeatedly to seat new brake pads you just installed. Turn off the engine and hold down on the pedal. Bleed the brakes again if the pedal sink within 15 to 20 seconds.

Posted on Dec 21, 2009

  • 1757 Answers

SOURCE: firing order of 2003 dodge grand caravan

For the 2003 Dodge Caravan (and Grand Caravan) ALL 3.3L V6 Engines (including the Flex Fuel): Also for 3.8L V6 Engines:

Firing Order:
1-2-3-4-5-6

Cylinders:
........(back).......
|...1....3....5...|
______________
|...2....4....6...|

Ignition Coil:
.......(back)
electrical connection
...........|
..........V
5........1........3
2........4........6
.......(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on Jun 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brakes bleeding


You need to fill up brake fluid to top,all wheels or one.someone have to pump brake and hold you open bleeder 4x or 5x times.put plastic tube end on bleeder bottom in bottle with some fluid.

Apr 28, 2013 | 2009 Dodge Grand Caravan

1 Answer

Put in a new master cylinder and the brake booster and bleed the brakes..... brake still not catching... goes almost to the floor.... What next? (2006 dodge grand caravan)


have you replaced the front and rear brake pads (for older vehicles, rear wheels use brake shoes instead of brake pads). if yes, check your calipers. completely remove it from your tire and have it cleaned.
if the problem still persists, then its time to replace your hydrovac

Aug 05, 2011 | 2006 Dodge Grand Caravan

2 Answers

I have a 2009 doge caravan and i just try to change the rear breakes but the caliper is not going back. i try a clamp but stil not going back, i open the main brake fluit bottle to release presure but...


Rear brake pads last about 70,000 miles,that is 5 years or more !!!

Turn the parking brake in,turn the caliper piston in first,then compress piston.

Ratchet park brake up ,after back together and system bleed (all 4 corners)

Oct 16, 2010 | 2009 Dodge Grand Caravan

1 Answer

How do I compress the cylinder in changing the rear brakes of the 2008 dodge grand caravan


If these are drum (not disc) brakes, you should be able to just open the bleed screw a bit (on the back side of the backing plate), and push the pistons back in as you install the new shoes.
Bleed the brakes as normal when you are finished.

Oct 03, 2010 | Dodge Grand Caravan Cars & Trucks

1 Answer

2005 grand caravan, right front brake drags and causes the rotor to heat up


bleed your brakes you possibly have air in the system, but instead of just bleeding one, bleed them all flush the old fluid out, make sure that when your bleeding your have a good eye one the resivoir to ensure that it doesnt get low, if it does and sucks air, youll have to do the process again. ideally youll need three people to do this correctly. person #1 to pump and hold the brakes. person #2 to monitor and add fluid to the resivoir, person #3 to bleed each brake. remember to bleed the brakes only after the person has pumped them up 10 full pushes of the brake, and then on push 11 hold the brake. then this is the time you would crack the valve to bleed the brake. the person in the driver seat will notice the brake goes to the floor. thats when you close the valve and do this again (pumping them up, holding , and then bleeding them), this is when the person monitoring the resivior will be adding more fluid. id do this to each brake 3 times to ensure all the air is out.

Aug 09, 2010 | 2005 Dodge Caravan

1 Answer

Remove master cylinder 1996 dodge caravan 2.4


disconnect brake lines from MC should be only 2. Remove the 2 nuts holding the MC on. replace in reverse order u will need to bench bleed the new MC and u will probaly need to bleed the brakes

Apr 13, 2010 | 1996 Dodge Caravan

1 Answer

BRAKE PEDAL GOES ALMOST TO THE FLOOR, DASH LIGHT ON FOR BRAKES, PEDAL APPEARS SPONGEY.


SOUND LIKE AIR IN BRAKE LINES.CHECK BRAKE FLUID LEVEL MAKE SURE ITS NOT LOW. CHECK ALL BRAKE HOSES AND BRAKE LINES. FOR LEAKS. YOU HAVE TO BLEED BRAKES.IF ALL IS GOOD.YOU HAVE MASTER CYLINDER AND ABS BRAKE FAILURE.HAVE DEALERSHIP FIX IT.THEY HAVE THE EQUIPMENT TO TROUBLE SHOOT AND BLEED THE BRAKE SYSTEM.

Sep 12, 2009 | 1995 Dodge Grand Caravan

2 Answers

Can't find where/how to bleed back brakes 2000 dodge grand caravan


The problem isn't at your brake calipers. Your rotors have a slight warp to them causing your vibration when you stop.

Sep 01, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...