Question about 2003 Cadillac CTS

1 Answer

How do i get the brake booster off my car

I can get everything off to take the booster out but cant turn it . any soulutions

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 577 Answers

It turn counter clock ways, there is a tab you will probably have to bend a little to let it rotate, the tab locks it in place when new one is rotated into place

Posted on Jul 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need to remove brake booster on 2001 93 auto convertible from fire wall

Jack, Have not done a SAAB brake booster myself, hoping links below will help you out. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Walk me through brake booster replacement
9 5 Brake booster replacement the easier way
saab 9 3 brake booster replacement Google Search

Jul 04, 2016 | 2001 Saab 9-3

1 Answer

Trouble removing ford focus booster brake valve

Did you disconnect the rod from the brake pedal to the booster?

Feb 13, 2015 | 2006 Ford Focus

1 Answer

Have a 1991 dodge dakota, have replaced everything , still cant get brakes to work.

How about the rubber flex hoses restricted

In the rear you have an abs hcu you can throw way
& bypass,then unplug the controller up under the dash
on the passenger side

Also the rear brake cables won't work for rust,they have to go also

I had a 1992 Dakota for 18 years

Leave the wire off the proportioning valve as the vehicle is wired wrong & if your bleeding it ,it will melt down the wires in the ignition switch (been there) Vehicle is not the same as the factory wiring diagrams

Mar 26, 2014 | 1991 Dodge Dakota

1 Answer

Brake booster removal

Disconnected the rod from the brake pedal?

Mar 09, 2014 | 2008 Dodge Avenger

1 Answer

Diagram for a brake booster

you cant rebuilt brake booster, have to buy new one

Nov 22, 2011 | 1990 Toyota 4Runner

1 Answer

I cant find the brake booster


Sep 20, 2011 | 1991 Plymouth Voyager

1 Answer

Spongy brakes

So long as the brake booster is working, test it by turning on the engine, press the brake pedal all the way down, then shut off engine keeping your foot on the brake pedal, if the pedal comes up slightly pushing against your foot then the booster IS working.

Did you BLEED the brakes??????

Mar 29, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Replace my master cylinder and booster

ok to replace it is preety straight foward..the master cylinder is built onto the booter (its where u put the brake fluid)

  • locate master cylinder and booster..
  • remove hoses and connections (remember where everything came from) take pics if you have to
  • unbolt and remove both cylinder and booster
  • bolt up new booster and cylinder
  • connect hoses and other connections..
  • fill with fluid.
now you have to bleed your brake lines

locate brake line on front wheel (its in the back,, cant miss it)
slacken one of the valves or remove the hose..
plug line with finger
pump brake a few times until it gets hatd and hold it down ,, release line brake will get soft
repeat a few times ,connect back line.

thats it your done..

dont forget to rate me if you find this helpful

Mar 20, 2010 | 1997 Chevrolet Blazer

1 Answer

Brake booster is not holding brakes when turned on only works when off or unpluged

the diaphragm in the brake booster is probably ruptured, replace booster

May 02, 2009 | Chevrolet Camaro Cars & Trucks

1 Answer

No brake power

faulty remanufactured master cylinder. always buy new.... i was trying to nsave some money and it cost me more in the long run

Dec 03, 2008 | 1992 Toyota Pickup

Not finding what you are looking for?
2003 Cadillac CTS Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides