Question about 1992 GMC Sierra

Open Question

How To Replace Temp Sensor for a 1992 GMC Sierra 4.3 L engine?

4.3 liter v-6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: 2007 gmc sierra 2500 IAT sensor

Well, the IAT (Intake Air Temperature) sensor is located on the air intake duct between the filter and the throttle body (Assuming you have the 6L motor). The wires are easily visible at the plug that connects the sensor to the wiring harness. That's the easiest place to access them.

Posted on May 18, 2008

Ad
  • 1118 Answers

SOURCE: Replace starter on 1992 GMC Sierra pickup truck

First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.

Posted on Feb 14, 2009

  • 14 Answers

SOURCE: 2004 gmc sierra

P0102 is mass air flow sensor circuit, low input the MAF is attached to the air cleaner where the hose runs out of it... Unplug it and check the voltage supply and the ground... looking into the plug, with the tab facing up, there will be 3 connecters inside it, left to right they are.... sensor signal, ground and supply.... make sure you have 12 volts at your supply and the ground is good good luck

Posted on Feb 28, 2009

canbruce75
  • 1776 Answers

SOURCE: how to replace a water pump on a 5.3 liter sierra

I suggest that you visit the autozone.com website and register the vehicle. It doesn't cost anything and will give you access to an online repair manual. The steps for replacing the water pump should be available there. Hope this helped and best wishes.

Posted on Aug 31, 2009

  • 11 Answers

SOURCE: como hago para poner a tiempo el motor de gmc

you need to disconnect the wire in the rh floor board of cab and then you can check timing.

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 GMC C1500 Sierra, 5.7 liter, 2WD. Replacing a one-lead ECT sensor with a two-lead??


Your engine coolant temp sensor is a two wire sensor.
The temp sending unit for temp gage is a different animal, one wire connector.
1994-gmc-c1500-sierra-5-7-liter-353htx05o4bsbc2sdlg1ra32-3-0.jpg

Nov 14, 2016 | GMC Cars & Trucks

1 Answer

What is the sparkplug firing order for GMC Sierra pickup truck with a 5.7 liter engine


1-8-4-3-6-5-7-2

Driver side cylinders, starting at the front of the engine, are 1,3,5,7

Passenger side, starting at the front, are ,2,4,6,8

Hope this helps.

Feb 24, 2015 | 2003 GMC Sierra 1500

1 Answer

The firing order for a 1993 2500 GMC Sierra


V-8 engine firing order is: 1-8-4-3-6-5-7-2

4.3 liter V-6 firiing order is: 1-6-5-4-3-2

Jul 29, 2014 | 1993 GMC Sierra K2500

2 Answers

I have a 1995 GMC sierra, 305/4l60e, I have been troubleshooting a running lean problem, finally got obd 1 software, all sensors are working in parameters, but I am losing my timing advance, my knock...


Your "knock sensor" kicks in??? That means there must be a knock detected and the engine is doing what it is supposed to do. How do you know your timing is 4-6 degrees at 60 mph?

Oct 30, 2013 | 1995 GMC Sierra C1500

1 Answer

I replaced the sensor, thermostat and the temperature gauge on my 1992 GM Sierra 1500 still does not work. What could my problem be


Try taking the wire of the temp sender unit and touching the engine and see if the gauge goes up to hot. If so then replace the temperature sender unit ( different to the sensor unit)

Oct 13, 2013 | 1992 GMC Sierra C3500

1 Answer

Where is the knock sensor located on 1992 chevy 5.7 liter engine


it is on the side of the engine block next to the starter

Jun 30, 2012 | 2000 GMC New Sierra 1500

1 Answer

I need a diagram for 1993 gmc sierra 1500 truck firing order from dist. to plugs


Sierra 1500 also C/K Series have three engine sizes; check this...

1993 GMC C 1500 P/U 5.0 liter V-8 VIN "H"

zjlimited_331.gif


1993 GMC C 1500 P/U 4.3 liter V-6 VIN "Z"

zjlimited_332.gif


1993 GMC C 1500 P/U 5.7 liter V-8 VIN "K"

zjlimited_333.gif


Hope helps (remember to rate this answer).

May 03, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

Where can I find the diagram for a 1992 GMC Sierra distributor cap? I need the firing order


The GMC 1500 Sierra have several engine sizes, hope this helped...

1992 GMC C 1500 P/U 2WD 4.3 liter V-6 VIN "Z"

d9ffbf1.gif



1992 GMC C 1500 P/U 2WD 5.0 liter V-8 VIN "H"

6e77604.gif



1992 GMC C 1500 P/U 2WD 5.7 liter V-8 VIN "K"

18df209.gif


Good luck, and remember rated this. TY for using Fixya.

Mar 31, 2010 | 1992 GMC Sierra

3 Answers

What transmission will fit in an 89 gmc sierra?


if it has a 4.3 liter motor a 86 to a 97 if it has a 350 motor a 81 to a 96 will work hope this helps

Nov 20, 2008 | 1989 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...