Question about Cars & Trucks

1 Answer

How to filling up and bleed master slave cylinder on a 2006 mazda6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,223 Answers

Go to www.automecanico.com translate this amazing website with your browser and fix it.
God bless you

Posted on Jul 19, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Hydraulic clutch problems

i have a ktm 125 wich all ktms have hydraulic cluthcs and i have the same problem as all these fellas even when im riding it just sucks right down all the fluid reply to me on X-KTMrida-X@hotmail.com ok thanks fellas

Posted on Oct 27, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

johnthejag
  • 286 Answers

SOURCE: bleeding the slave cylinder

Hi

Best to get the help of a friend to pump the clutch pedal for you.

Take care with the brake fluid, as it removes paintwork !

Top up your clutch fluid reservoir, connect a bleeding tube to the nipple on your slave cylinder, and put the other end of tube in a container.

Get your friend to pump pedal 3 times, and then hold to the floor.

Open the nipple for 5 seconds or so, then close.

Repeat this about 6 to 8 times topping up the fluid as you go.

You should then find, that the air is out of your system, and your pedal is back to normal !

Good luck !

A FixYa rating would be nice.... Thank you ! John.



Posted on Feb 10, 2009

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed clutch, master cylinder, slave cylinde, folk but still cannot get any clutch


You may still have air in the system
Try filling the reservoir again and bleed out the air at the slave cylinder
Use a friend to pump up the clutch pedal then get him to hold the pedal down while you bleed the slave cylinder.

May 10, 2016 | Cars & Trucks

1 Answer

Wheres the slave cylinder located at? wen i press my pedal it stays at the floor.what could that be?


Hello Herman, I assume that you are referring to the clutch slave cylinder. Did you check the fluid in the clutch master cylinder? Fill the master cylinder and try it a few times. If it works better but not good enough, you may need to bleed the clutch system. The slave cylinder should bleed at or near the front on the side of the transmission.

Apr 11, 2015 | 1999 Pontiac Sunfire

1 Answer

Bleeding hydraulic clutches


Did you replace the master or slave cylinder?
If you replaced the clutch master cylinder, make sure you bench bleed it before you install it. Bench bleed it by getting a "bleed kit" (plastic fittings that screw into the hole where the hydraulic line connects to it, and a couple of hoses) secure the master cylinder in a vise (don't crush it, just hold it firmly), insert the plastic fitting and attach a hose. Fill the reservoir with brake fluid, then route the hose back into the fluid within the reservoir. insert a rod into the end of the master cylinder where the brake rod goes, then slowly push in and out until you don't see any more bubbles.
Then remove the plastic fitting and quickly install. Make sure to keep some rags handy to put under the master cylinder as it will leak a little while you're trying to get it installed. Keep in mind that brake fluid can ruin your paint, so wipe any off immediately.

If you replaced the slave cylinder and it's not bleeding, you can connect a long vacuum line to the bleeder valve on the slave cylinder and hold it in the master cylinder fluid reservoir. have someone pump the clutch slowly until all of the bubbles are gone, then bleed it the "old-school" way, by opening and closing the bleed valve while someone pumps for you.
Hope this helps

Jul 23, 2014 | 2006 Mercedes-Benz Vito 112

1 Answer

How to change a clutch master cylinder on a 2006 toyota tacoma


remove line from the side of clutch master cylinder two bolts or nuts on firewall inside vehicle is a pin on the upper side of clutch remove and pull old unit out bench bleed new master by filling and pressing in on the piston of the master cylinder. if you dont have a hose fitting dont bench bleed bleed it in vehicle( this method takes longer) install back in vehicle and hook it all back up torque bolts to 25 ft lbs then bleed the slve cylinder from under vehicle near back of motor just like bleeding brakes pump up hold and release the line pressure by opening valve on slave cylinder.

Apr 06, 2013 | 2006 Toyota Tacoma

1 Answer

I have a 1988 f350 diesel i replaced the clutch master cylinder and the slave cylinder bled the lines and the truck still wont go in gear the throw out arm is moving about 1/2 inch what could be my prob


Ford has special bleeding and blocking instructions for clutch slave. Check manual for proper bleeding requirements. May consider presurre bleeding of master cylinder or use master cyclinder bleeding tubes that fill the resevoir as you bleed the and remove all air in system.

Jan 21, 2013 | Cars & Trucks

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

1 Answer

Are the brake master cylinder and the clutch slave cylinder interconnect in some way? I'm told that the slave cylinder get its fluid from the master cylinder.


The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.

Jul 28, 2010 | 1995 Ford Escort

1 Answer

Changed clutch but unable to bleed the slave cylinder. Does that mean clutch master cylinder is bad? Got one from parts store but can't figure out how to take the clutch safty switch off to change it. Any...


Probably not. Bleeding clutch slave cylinders is tricky because you cant "pump it up". The master cylinder has no static valve so the best way to bleed the slave cyl. is to use gravity. Fill the master cylinder reservoir and open the bleed valve on the slave cyl. Allow fluid to drip into an open can until there's no trace of air. Close bleed valve and try clutch. If still no pedal, repeat the process. This is quite an acceptable procedure.

Mar 22, 2010 | 1991 Chevrolet S-10

2 Answers

The clutch filud was empty filled but still can't ingae clutch. Is there a bleeder some were


There should be a bleed valve on the slave cylinder but some of them are quite difficult to get to. If the master was empty you need to check the line for leaks and the master and slave cylinders for leakage.

Jan 16, 2010 | 2002 Ford Ranger Regular Cab

2 Answers

How do I bleed the master clutch cylinder


Drain or bleed? The bleeder nipple is on the slave cylinder. Fill master cylinder,leave the cap loose, open the bleed nipple at the slave cylinder,and let gravity do the rest. whe vo more aie bibbles come out and it drips steady. Close the bleeder, top of the master cylinder and you are done.

May 30, 2009 | 1996 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...