Question about 1999 Nissan Quest

1 Answer

Thermostat location how is the old thermostat replaced

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 21,873 Answers

You'll probably need a repair book. It should be behind a housing on the side of the block behind the belts.

Posted on Jul 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace Thermostat on 2006 Town & Country Van ?


drain coolant system half way until coolant below thermostat.to locate thermostat follow upper radiator hose to engine.just remove both thermostat housing two bolts then clean all traces of old gasket material. be sure to have new thermostat gasket and gasket sealer on hand.make sure both thermostat housing and engine block clean dont have any traces of old gasket material if so you will have coolant leak.but besure to put gasket sealer both sides thermostat gasket just need thin layer RTV silicone.you can buy can of gasket remove to help remove old gasket material. try not to damage thermostat housing surface or engine surface with scraper deep scratches cuts in either surfaces will cause coolant leak be careful.

Dec 28, 2012 | Chrysler Cars & Trucks

1 Answer

Thermostat needs replaced


To replace a thermostat, you will need at least: 1. A new thermostat 2. Screwdriver 2. Needle-nosed pliers. Depending on the thermostat and location in your home, you may need more. Make sure the new thermostat you are using to replace the old one with is compatible to your 110-volt housing circuitry. Always turn off the electrical power to the home thermostat at the power panel or circuit breaker box.--------------------------------------------------------------------------
carbrain c168 scanner

Dec 01, 2012 | 1996 Pontiac Grand Am

1 Answer

How do u replace the thermostat? Where is it located?


Locate your thermostat if you haven't already done so.

Most thermostats are located where the top radiator hose joins the engine, so these steps deal with this type. If your thermostat is in the bottom radiator hose, the principle is the same.


2Place a bucket under where you're going to be working.

Some fluid will escape, so have a clean two-gallon container handy to catch it, and return the fluid to the radiator when you finish the job.


Remove the clamp.

Follow you radiator hose to where your thermostat is located.


4Pull off the hose.

This is when some fluid will escape and drain into your bucket.


5Remove the bolts that hold the thermostat housing in place and lift out the old thermostat.

Compare the new thermostat and its gasket with the old ones. If the new thermostat and the gasket that's included with it aren't exactly like the old ones, go back to the store for the right ones.


6Lay the new gasket in place.

There's a gasket around the hole where the thermostat was located - take that off, too. Scrape off any pieces of gasket that may be stuck, but be sure not to let these pieces fall into the hole!


7Drop in and secure the new thermostat.

Make sure to place the spring-side down; then replace the bolts.


Replace the hose and hose clamp.

If your hose clamp uses screws, screw it down tightly but not tight enough to cut into the hose.


Replace whatever fluid ran out of the hose by pouring it from the container into the radiator fill hole or coolant reservoir.

Be sure not to pour it on the ground where children and animals can be endangered by it. If you accidentally spill fluid, wipe it up thoroughly before hosing down the area, and then place the rags in a sealed plastic bag before disposing of them.


Custom Wheels For Honda

Jun 14, 2012 | Cars & Trucks

1 Answer

Need to replace the thermostat on my 2002 buick la saber, where is this located?


The thermostat is normally located in the aluminium elbow that the top radiator hose connects to. The elbow is usually held down by two bolts and it is only necessary to remove these to replace the thermostat. It may not be necessary to remove any hoses. Take care that the new thermostat is correctly located in its recess and the old gasketing has been completely removed and that the new gasket has a smear of gasket cement on it. While tightening the bolts, make sure that the elbow is seating evenly and not catching on the edge of the thermostat or you could crack the elbow.

Feb 21, 2011 | 2002 Buick LeSabre

1 Answer

2002 Audi 4.2. Where is the thermastat located


Thermostat is located in front of the engine between V cylinder banks, for Audi 4.2 V8.

34c731c.jpg

6879319.jpg
Remove the thermostat housing (2 bolts) and the old thermostat. Note the orientation of the old thermostat (vent valve facing UP). Clean both thermostat housing and block surfaces and remove all traces of old gasket material. Install the new thermostat vent valve facing UP.
Please rate my response. Thanks!

Aug 25, 2010 | 2000 Audi A6

1 Answer

Where is the thermostat located on a1995 Olds


Follow the top rad hose to the engine, the bit the hose attaches to on the engine is the housing that houses the stat

Nov 21, 2009 | 1995 Oldsmobile Cutlass Supreme

2 Answers

How do i change a thermostat??


buy the correct thermostat and thermostat gasket for your car, then locate the upper radiator hose. Where the upper hose connects to the engine there should be a two bolt hose connection/ thermostat housing ( could be 3 or 4 bolt, but most are 2) these bolts should be removed and then gently lift the hose and hose connection/thermostat housing exposing the old thermostat. note the position then replace the new thermostat just as the old was installed.

Oct 27, 2009 | 1996 Ford Contour

1 Answer

Is it a major undertaking to replace a thermostat?


no not major !! Locate the upper radiator hose and follow it to the engine the thermostat is located at the connection to the engine in the metal housing that the hose is hooked to, Just remove the two bolts that hold the housing on and remove the old thermostat scrap off the old gasket and replace the thermostat and gasket also use silicone sealant on the new gasket and now re-install the housing on the engine!! Check coolant level and refill if needed ! Check for leaks if none then you are good to go!! swampratt200 AAAEEE!!!!

Jul 21, 2009 | 2003 Nissan Xterra

2 Answers

Thermostat replacement


go to www.autozone.com and look in the compounts list for that year car and it will tell you excatly wher it is located.

Feb 19, 2009 | 1992 Toyota Celica

Not finding what you are looking for?
1999 Nissan Quest Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...