Question about Cars & Trucks

Open Question

Cylinder head torque settings for renault clio 1.2

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Please can anyone help need torque setting's for my cylinder head on my clio 1.4 16v 2004 & order too tighten down


they are stretch bolts and can only be used once. If you try re-using the old bolts they are likely to break or fail to apply enough pressure smile.gif Torques and the order are listed here.

http://ww2.justanswer.com/uploads/nabilc/2011-04-11_205136_cas.pdf

Apr 09, 2016 | Cars & Trucks

1 Answer

What is torque setting on renault megane 1.5 dci (2004)?


I assume you are looking for cylinder head tightening torque specifications?

Stage 1: 25nm
Stage 2: 25nm
Stage 3: 90 deg
Stage 4: 90 deg
Stage 5: 90 deg +- 10deg

Yes that is correct- a total of 270 degrees!

Hope this helps!

Apr 27, 2014 | 2004 Renault Megane

1 Answer

Torque settings clio 1.5 dci big end shells


whats the torque setting for big end bearing bolt and cylinder head bolt for toyota corolla 12 valve 2E,1990.

Jan 12, 2010 | 2000 Renault 181

1 Answer

Cyl head torque renault clio 1.4 1998


Its very very complicated - Ach! the french!!! ---- Stage 1 torque to 20nm ----------- Stage 2 - wait 3 minutes.---------- Stage 3 - fully slacken all bolts in sequence------- Stage 4 - torque to 20nm-------- Stage 5 - tighten by 97 degrees (plus or minus 2 degrees - so 95-99 degrees really)--------
Tightening sequence, with the flywheel on the right looking down on engine - top row of bolts are 1,2,3,4,5 -------- bottom row of bolts are 6,7,8,9,10 --------- sequence is, 8,3,4,9,7,2,5,10,6,1----

Dec 08, 2009 | 2007 Chevrolet Impala LS Sedan New Cars

2 Answers

Angle Torque settings head bolts


Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Jan 28, 2009 | 2000 Renault Sportwagon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...