Question about Cars & Trucks

Open Question

Timing marks opel kadett. where is the mark for crank pulley. 1,6l and 1992 model

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 28 Answers

SOURCE: crankshaft pulley timing marks

the red mark is where the timing is supposed to be after u have bypassed the electronic advance.the first white line on the left is tdc.
thanks for useing fixya

Posted on Aug 18, 2008

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

gregstobbe
  • 56 Answers

SOURCE: timing mark for charade 90 model 3 cylinder

here is the site for timing marks.
http://www.2carpros.com/car_repair_information/tec_info/1990/daihatsu/charade/1990_daihatsu_charade_timing_belt_diagram_marks.htm
Ps. dont forget to rate my solution please. Thanks.

Posted on Dec 27, 2008

jpstuhr
  • 49 Answers

SOURCE: 1983 civic 1500 timing

At slow idle and Before Top Dead Center, unless otherwise specified.

1981-89: Leave Distributor vacuum hoses, as equipped, connected.
a4d88ba.jpg ea4458f.jpg

Posted on Feb 12, 2009

emissionwiz
  • 76132 Answers

SOURCE: 1992 Volvo 960 Broken timing belt

IF U BROKE THIS BELT WHILE DRIVING U HAVE BENT THE VALVES IN THE ENGINE, THIS IS WHAT IS CALLED AN INTERFERENCE DESIGN ENGINE, THAT MEANS WHEN THE TIMING BELT BREAKS THE PISTONS HIT THE ENGINES VALVES

Posted on Nov 11, 2009

Testimonial: "THanks - was not able to accept this last answer, but thankfully I found another way to say THANKS. That notch was suspicious!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Opel kadette has no power and backfires when I over rev it refuses to go up any hills and has a continues miss fire


It sounds like your firing order is out or your timing is out or you have fuel starvation.
I believe the firing order is 1-3-4-2 on your car. Only English Fords had a firing order of 1-2-4-3 and VW beetles are 1-4-3-2.
Next. check the timing. You should have a spark on no 1 cylinder when the timing mark on the front pulley is about 16 degrees from top dead center - there is a mark on the pulley to show these positions. If you don't know how to check it, take it to a service agent.
Make sure your fuel filter is clean - replace it, they are cheap - and then make sure you have good fuel flow to the carburetor.
Finally, you could have burnt valves. This will mean taking off the cylinder head and reseating or even replacing burnt valves. This could be a costly job and should be done by a qualified technician.

Mar 12, 2015 | Opel Kadett Cars & Trucks

1 Answer

I changed my timing belt on my 2002 1.6 ecotec opel astra cde. i got the timing belt marks wrong . how must the cam pulley marks be when i got the crank on tdc please.


remove the rocker cover and look on the ends of the cams ,their are slots and they align with the head ,i use my old spanner from my angle grinder its just about the right thickness ,lower pistons to the middle then set the cams ,make sure no1 the valves point up and outwards like a V victory sign then bring the no1 piston up to TDC ,i take the plug out and use a long thin screwdriver for this .then put the belt on

Dec 06, 2014 | Opel Cars & Trucks

1 Answer

Timing marks on astra x18xe dohc


If you mean the crank position marks then they are likely to be visible through a small window in the top of the bellhousing which may require removal of various items to allow you to look in with a flashlight. Have someone turn the engine slowly and you will see the marks come into view. There may be more than one and a workshop manual may be a good investment.
Other timing marks will be on the pulley end which may not be very visible and may require removal of the inner wheelarch plastic liner and removal of the front right wheel.

Jun 03, 2014 | 2009 Opel Astra 1.4

1 Answer

Need timing marks firing order


1342 firing order, timing marks located on lower timing belt cover; notch on crank pulley for TDC (top dead center). Distributor cap should have cyl#1 marked, clockwise rotation.

Nov 12, 2013 | 1992 Toyota Tercel

1 Answer

Timing marks on engine


Use the timing marks on the damper for the crank and bring it to 0 on the cam there are marks that correspond with a mark on the head. Look on autozone dot com and put in the year make and model then look at the free repair guides.

Oct 09, 2012 | 2001 Opel Corsa 1.4

1 Answer

Change timming belt. where marks have to be set? 92 dodge colt


I lost you, stupid computer. Anyhow there are 8 different engines for the dodge colt in the early 1990's I can only assume its the 1.4L, 1.5L or 2.4L. The 1.4L & 1.5L the timing marks are exactly the same. The Cam points to 3:00 marks ther. The crank points almost straight up, slightly to the right, mark on engine cover. The 2.4L has 3 marks, The crank has an alignment mark at approximately 10:00, the cam sprocket points straight up at 12:00 and the idler pulley (to the right of crank shaft pulley) points approximately 11:00. They should all have a notch or mark when aligned. The short secondary belt, the crankshaft should be in the same location 10:00 and the balance shaft (to the left) should be at 9:00. This goes on after of course. Rotate engine 2 full revolutions and recheck marks before starting engine.

Feb 02, 2011 | 1992 Dodge Colt

2 Answers

Where is the timeing mark on a 1992 honda civic 1.5 16 valve


This was listed under the 1994 Honda Civic by the Asker for a 1992 Honda Civic
Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1992 Honda Civic. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/1992/make/honda/model/civic/1992_honda_civic_timing_belt_diagram_marks.htm

Mar 29, 2010 | 1994 Honda Civic

1 Answer

Timing marks dohc


the timing marks are located on the gear/pulley system. the crank pulley and the cam shaft pulley.

Dec 16, 2009 | 1992 Mazda Protege

1 Answer

Need diagram showing timing adjustment for a 1992 honda accord 2.2 engine see no timing marks how do i set timing


Check the position of the timing marks. The timing pointer mustbe perfectly aligned with the TDC (white mark) on the flywheel orflex-plate; the camshaft pulley must be aligned so that the word UP isat the top of the pulley and the marks on the edge of the pulley arealigned with the surfaces of the head. Additionally, the face of thefront timing balancer pulley has a mark which must be aligned with thenotch on the oil pump body. This pulley is the one to the left crankwhen viewed from the pulley end.

Also, in here, 1994-Honda-Accord-Coupe-Section-01-Engine (page 47 and next / TDC marks) you can find referenece information about Accord Engine.

If you need more details, visit autozone.com (free register) and select your model vehicle.

I hope help you (remember rated this help) Good luck.

Sep 25, 2009 | 1992 Honda Accord

2 Answers

Opel Corsa timing belt replacement


You need to find the timing marks on both crank and cam pulleys, set it, then take of the belt ane dont let any pulley move! Put on new belt and set the tension of the belt.

Jul 31, 2009 | 2000 Acura Integra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...