Question about Dodge Durango

Open Question

Location of camshaft sensor on 4.7 dodge engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Cam Shaft Sensor Problems

Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Posted on Dec 29, 2008

  • 2 Answers

SOURCE: location of the camshaft and crankshaft sensors

cam sensor is on the driver side, front of the motor, just below the valve covers in easy veiw, just outboard of the water temp sensor and they both share the same wiring harness.  The cam sensor is on the passenger side, actually on the transmission bell housing.  It takes the signal from the flywheel next to the ring gear, about an inch from the engine on the transmission bellhousing.  Accesible from the top and easier if you remove the air filter duct.  Or jack up the front passenger side and easier if you come in from the front and its behind the axel, behind the motor, go up the bell housing, just below crank shaft level.  Go with this first , it tells the comp when to send fuel.  If you're getting spark with a 1381 code and you're choosing between CAM & CRANK, start with this, this is the culprit.  Consider getting it from the dealer.  Good luck.  This is Waverunner70, Hope I could help.

Posted on Mar 05, 2009

JShreader
  • 50 Answers

SOURCE: location of camshaft sensor on a 3.5 dodge intrepid

The Camshaft Position Sensor is installed in the Timing Belt Housing Cover above the Left Camshaft Sprocket. Below is a couple of pictures...
5e46f38.jpg

58444d6.jpg
I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader.

Posted on Mar 31, 2009

  • 51 Answers

SOURCE: locating and replacing a camshaft sensor in a 2005 dodge neon

this is a very very simple procedure. you do not need pics. there is a sensor located at the end of the engine on the far side from the belts. at the top. it has a plug with two wires in it. just remove the two 10mm bolts un hook the plug and reverse the process to reinstall. if you have a factory intake you may have to remove it to access this sensor. just the intake tube.

Posted on Aug 08, 2009

  • 236 Answers

SOURCE: 2001 dodge ram 1500 5.9 camshaft position sensor

CAMSHAFT POSITION SENSOR 2001 Dodge Truck RAM 1500 1/2 ton 2WD 5.9L SFI 8cyl The Camshaft Position Sensor is located: Under hood, center, upper engine area, rear of intake manifold, mounted in distributor

If this is helpful.Please leave ositive Feedback. Thanks, SnugglePants

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Diagram of where a camshaft sensor is on a dodge stratus 2.4L 4 cylinder


2003 model
not confirmed
crank angle sensor might be near the stater motor on the block


26233366-qzmmc3ihqjw1j4mumdlnccct-4-0.gif

26233366-qzmmc3ihqjw1j4mumdlnccct-4-2.gif

Jul 07, 2016 | Dodge Cars & Trucks

1 Answer

Where is the camshaft position sensor on a 1998 Dodge Dakota 5.2L


The camshaft position sensor is located on the distributor for all engines designed for the 1998 Dodge Dakota. Accessing the sensor requires removing the distributor cap and the distributor rotor. The camshaft sensor pigtail comes through the front of the distributor and connects to the engine wiring harness above the intake manifold.

Oct 03, 2012 | Cars & Trucks

2 Answers

How do I replace the CAM sensor on a 1996 dodge neon?


Hi, my name is John I will do my best to assist you.

To Remove
  1. Disconnect the negative battery cable.
  2. Disconnect the filtered air tube from the throttle body and air cleaner housing.
  3. For SOHC engines, remove the air cleaner inlet tube.
  4. For SOHC engines, detach the electrical connectors from the engine coolant sensor and the camshaft position sensor.
  5. For DOHC engines, unplug the electrical connector from the camshaft position sensor.
  6. For SOHC engines, remove the brake booster hose and the electrical connectors form the holders on the end of the cylinder head cover.
  7. Unfasten the camshaft position sensor mounting screws, then remove the sensor.
  8. Loosen the screw/bolt attaching the target magnet to the rear of the camshaft.
To Install: NOTE: The target magnet has 2 locating dowels which fit into the machined locating holes in the end of the camshaft.

  1. Install the target magnet in the end of the camshaft. Tighten the retainer to 30 inch lbs. (3.4 Nm).
  2. Install the camshaft position sensor. Tighten the sensor mounting screws to 80 inch lbs. (9 Nm).
  3. For SOHC engines, place the brake booster hose and the electrical harness in the holders on the end of the valve cover.
  4. Attach the electrical connector(s) to the camshaft position sensor and coolant temperature sensor (if necessary).
  5. Install the air cleaner inlet tube and the filtered air tube.
  6. Connect the negative battery cable.
The camshaft position sensor is mounted to the rear of the cylinder head - SOHC engine shown


tecnovative_139.gif
Location of the camshaft position sensor - DOHC engine shown

tecnovative_140.gif

Unfasten the retaining bolt, then remove the target magnet from the rear of the camshaft - SOHC shown, DOHC similar

tecnovative_141.gif

The target magnet has 2 locating dowels for proper alignment during installation

tecnovative_142.gif

Feb 20, 2011 | 1996 Dodge Neon

1 Answer

Just wondering where the Camshaft position sensor in my 2005 Dodge Neon is as I need to replace it.


Removal & Installation 2.0L engine camshaft position sensor location chry_car_2.0_cpsloc.gif

2.4L engine camshaft position sensor location chry_car_2.4turbo_cpsloc.gif

2.0L SOHC Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Brake booster hose and electrical connector from holders on end of cylinder head cover and reposition
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
    • Sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor. Torque sensor mounting screws to 80 in. Lbs. (9 Nm)
    • Brake booster hose and electrical harness in holders on end of valve cover
    • Electrical connectors to camshaft position sensor
2.4L Turbo Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Air cleaner box
    • Plastic clip for the wiring harness from the stud on the valve cover
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose from the valve cover
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
  3. Remove sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor torque sensor mounting screws to 80 in. lbs. (9 Nm)
    • Electrical connectors to camshaft position sensor
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose to the valve cover
    • Plastic clip for the wiring harness to the stud on the valve cover
    • Air cleaner box
    • Negative battery cable
prev.gif next.gif

Aug 01, 2010 | 2005 Dodge Neon

1 Answer

Where is the camshaft sensor on a 2004 dodge neon sxt engine and how do i change it


disconnect the negative battery cable. the cmp sensor is located on the left end of the cylinder head. move thebrake booster hose and electrical wires out of the way to access the cmp sensor. disconnect the sensor plug by pushing the locking tab back toward the firewall. remove the 4 bolts from sensor and lift out sensor. remove the trox bolt which holds the target magnet to camshaft. when installing target magnet be sure to line up holes to dowels on end of camshaft. torque torx bolt to 30 in-lbs. be sure to install new o-ring on sensor and torque bolts to 80 in-lbs. (hallclifford)

Apr 08, 2010 | 2004 Dodge Neon

1 Answer

Diagnostic code P 340 and P 341 Camshaft Position Sensor Malfunction for a Dodge Ram Diesel 2500. What does it mean?


The Camshaft Position Sensor tells the PCM (computer) the position of the Camshaft Position. This Sensor sychronized along with several other Sensors including the Crankshaft Position Sensor the firing of the electronics to the spark plugs of each cylinder.
It is not difficult to replace and relatively inexpensive.
1. Disconnect the Negative side of the Battery,
2. Locate the Sensor and unplug.
3. Remove the Position Sensor retaining bolt.
4. Pull out the Sensor.
Replacement is reverse of above order.
Hint: use fresh engine oil on the end/sides of the Sensor especially around the rubber o-ring(s) to ease pushing the Sensor into proper position.

Nov 18, 2009 | 2005 Dodge Ram 2500 Truck

3 Answers

2001 dodge ram 1500 5.9 camshaft position sensor location?


CAMSHAFT POSITION SENSOR 2001 Dodge Truck RAM 1500 1/2 ton 2WD 5.9L SFI 8cyl The Camshaft Position Sensor is located: Under hood, center, upper engine area, rear of intake manifold, mounted in distributor

If this is helpful.Please leave ositive Feedback. Thanks, SnugglePants

Oct 21, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How hard is it to install a crank sensor and a cam sensor in a 2003 Dodge Caravan?


Crankshaft Sensor
2.4L 4 cylinder Engine Under the starter (30 minute)
3.3 L 3.8L 6 Cylinder located on the rear of the Tranmission housing above the differentail housing (45 minute)

Camshaft Sensor
2.4L 4 Clyinder Engine Rear Of Cylinder Head (30 minute)
3.3L & 3.8L 6 Cylinder Under the Throttle Body (30 minute)

let me know

Sep 21, 2009 | 2003 Dodge Caravan

4 Answers

Where is the camshaft position sensor located on a 2004 dodge stratus 4 cyl 2.4L engine


the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

Jul 08, 2009 | 2004 Dodge Stratus

1 Answer

Where is located the camshaft sensor on a dodge sx 2.0 2003?


camshaft sensor located on end of cylinder head near battery..remove battery..4 bolts and wire connector..clean mounting surface and install new sensor

Mar 14, 2009 | 2003 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...