Question about 2010 Volkswagen Routan

Open Question

Liftgate rear latch - 2010 Volkswagen Routan

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 MKX rear hatch will not opprat with buttons.Hatch was stoped when closing and now will only open by hand,but does have power.


Hatch or liftgate ?
Liftgate Release
The liftgate release switch operates the liftgate latch electronically. When the switch is pressed, the SJB processes the input and releases the liftgate latch.
The doors must be unlocked electronically in order for the SJB to release the liftgate latch. When this condition is met and the SJB receives the input from the liftgate release switch, the SJB provides power to the latch release motor.

SJB - smart junction box , fords BCM - body control module .
Your best bet , take it to the dealer .
B2666 Liftgate Release Switch Circuit Failure Go To Pinpoint Test I . B273A Liftgate Release Output Circuit Shorted to Ground Go To Pinpoint Test I . B273B Liftgate Release Output Circuit Open or Shorted to Battery Voltage Go To Pinpoint Test I .

Aug 24, 2017 | Cars & Trucks

1 Answer

Envoy hatch lock


There is a known TSB for this....
#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Apr 14, 2014 | GMC Envoy XL Cars & Trucks

1 Answer

Rear liftglass won't lock


#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Jan 17, 2012 | 2009 Saab 9-7X

2 Answers

Rear tail gate will not open


how to i open a stuck lift garte on a ford winstar 2000 lock broken too

Jun 14, 2009 | 2001 Ford Escape

1 Answer

2002 Explorer rear liftage latch replacement


Liftgate Latch Remote Control Removal and Installation
  1. Remove the liftgate trim panel. For additional information, refer to Section 501-05.
  1. Remove the watershield.
  1. Disconnect the actuator electrical connectors.
    a0023946.gif
  1. Disconnect the liftgate window glass latch release cable.
    1. Release the cable conduit.
    1. Disconnect the cable.
    a0023921.gif
  1. Disconnect the liftgate latch release cable.
    1. Remove the cable conduit.
    1. Disconnect the cable.
    a0023919.gif
  1. Release the exterior liftgate release handle actuating rod.
    1. Open the clip.
    1. Release the rod.
    a0023942.gif
  1. Remove the bolts and the liftgate latch remote control.
    a0023922.gif
  1. To install, reverse the removal procedure.
    • Transfer parts as necessary.

Jun 01, 2009 | 2002 Ford Explorer

1 Answer

2001 Ford Escape Rear Hatch won't unlock


The liftgate consists of the following components:
  • liftgate door lock actuator
  • liftgate lock cylinder (if equipped)
  • liftgate window glass
  • liftgate window latch/ajar switch
  • liftgate window glass release handle
  • liftgate latch remote control which consists of the following component:
    • liftgate release handle
  • liftgate latch, which consist of the following component:
    • liftgate latch door ajar switch
Liftgate Latch Actuator Removal and Installation
  1. Remove the liftgate latch remote control. For additional information, refer to Liftgate Latch Remote Control in this section.
SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual
REMOVAL AND INSTALLATION Liftgate Latch Removal and Installation
  1. Remove the liftgate trim panel.
  1. Disconnect the liftgate ajar switch electrical connector.
  1. Disconnect the liftgate latch actuating rod.
    1. Open the clip.
    1. Disconnect the actuating rod.
  1. Remove and discard the liftgate latch bolts.
  1. Remove the liftgate latch.
  1. NOTE: Make sure the liftgate latch release rod is not preloading the latch. It should be clipped in a relaxed state with no slack.
    NOTE: Position the liftgate latch release rod by pushing outboard to remove the slack.
  1. Remove the screws and the liftgate latch actuator
90f640f.gif

May 29, 2009 | 2001 Ford Escape

2 Answers

2003 where is the modules for the liftgate in a 2003 lincoln Nav


tascafordparts.com for discount.

The liftgate actuator and remote control are in the liftgate.
The module is in the left rear quarter trim panel.


SECTION 501-03: Body Closures 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Power Liftgate Module Removal and Installation
NOTE: Prior to removal of the power liftgate module, it is necessary to upload module configuration information to a diagnostic tool. This information needs to be downloaded into the new power liftgate module once installed. For additional information, refer to Section 418-01 .
  1. Remove the rear quarter trim panel. For additional information, refer to Section 501-05 .
  1. Remove the power liftgate module.
    1. Disconnect the electrical connectors.
    1. Remove the bolts.
89dd4de.gif
  1. NOTE: Once the new power liftgate module is installed, it is necessary to download the module configuration information from the diagnostic tool into the new power liftgate module. For additional information, refer to Section 418-01 .

-----------------------------------------------------------------------------------------

Principles of Operation
The power liftgate is controlled by the power liftgate module.
The power liftgate module receives inputs from:
  • glass position switch (determines the ajar status of the liftgate glass).
  • forkbolt switch (determines the primary position of the latch).
  • detent switch (determines the secondary position of the latch).
  • home switch (determines the power cinch status).
  • power liftgate control switch (activates the power liftgate from the interior of vehicle).
  • pinch strip switches (determines if an obstacle is detected between the pinch strip and liftgate).
  • instrument cluster module (activates and sets the options for the power liftgate).
  • optical sensor (determines the direction, travel speed and obstacle detection of the liftgate).
  • UBP serial communication link.
The power liftgate module sends outputs to:
  • liftgate motors.
  • power cinching latch system.
  • liftgate chime module.
  • body security module
------------------------------------------------------------------------------------

The liftgate consists of the following components:
  • liftgate window glass latch
  • door lock actuator (power liftgate only)
  • liftgate latch
  • liftgate handle
  • liftgate latch remote control (power liftgate only)
  • liftgate ajar switch
  • chime module (power liftgate only)
  • -------------------------------------------------

Apr 14, 2009 | 2003 Lincoln Navigator

2 Answers

2002 Explorer rear liftage latch replacement


Liftgate Latch Removal and Installation
  1. Remove the liftgate trim panel.
  2. Remove the watershield.
  3. Remove the bolts and the liftgate latch.
    • Discard the bolts.
    a0023920.gif
  1. Disconnect the liftgate ajar switch electrical connector.
    a0023947.gif
  1. Disconnect the release cable.
    1. Disconnect the cable conduit.
    1. Disconnect the cable.
    a0023919.gif
  1. To install, reverse the removal procedure.
    • Transfer parts as necessary.
gate latch.

Apr 10, 2009 | 2002 Ford Explorer

1 Answer

2003 Saturn Vue rear liftgate won't open


The easy part is you just need the latch for the liftgate. The hard part is getting to it and opening the liftgate to replace the latch. You should be able to pull the liftgate trim off most of the way with the gate closed and try to manually actuate the latch to open the gate. You may have to go so far as breaking the latch from the inside to open the gate and then replace your latch.

Nov 10, 2008 | 2003 Saturn VUE

1 Answer

PT Cruiser LAtch won't operate


If the latch won't operate when you use the handle, try inserting the key, turning it, and pulling up on the liftgate while the key is in the turned position (it won't stay there, so you need to hold it turned while you raise the liftgate.

Aug 06, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
2010 Volkswagen Routan Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...